Viewing all customer Discussions for:

81-126 Patio Sliding Glass Door Roller, Crossly

I looking to replace these worn out sliding door wheels. I would appreciate your help in identifying the correct replacement part. I need 4 sets. Regards, Subhasj.

Hi, The glass door on our screen porch has a broken wheel, but I can't find any identifiers on the brand or manufacturer. The entire porch looks like a kit (aluminum and vinyl). The glass door is solid, but this roller looks very flimsy. Can you help me find a replacement, please? Thank you. The r ... (cont.)

Please help try to identify the roller assembly for my sliding door.

Hi there,As I live in the U.K. t's a little tricky getting over to you!The question I have is in two parts:Part 1 - are there any other patio-sliding-door rollers that are compatible with your stock item 81-126?Part 2 - are there any double wheel rollers that could be used instead? In both cases I'm ... (cont.)

took out of very old aluminum frame door

..

I need to replace two rollers. The rollers have a specific fit to slide into the aluminum framing. I have one roller that works and allows me to adjust the height, but the other screw on the other older is rusted frozen. It says PATIORAMA on the door handle, and was likely installed in the late 6 ... (cont.)

Part number Delta 1176 roller from a Champion sun room sliding glass door. I assume the sun room and door rollerS are approximately 20 years old. Roller is 13/16 wide and approximately 2 3/4 inch long. I Could not find any parts that cross referenced the part number. Any help would be appreciated. ... (cont.)

I just purchased a 81-126 Patio sliding glass roller. WHAT IS THE SCREW SIZE OF THE THREADED SCREW THAT ATTACHES THE ROLLER TO THE DOOR FRAME? Is it 8-32 x 3/4 Phillips head? I need to buy new screws. Thank you

Need help finding a replacement patio door roller if it exist. The old patio doors have no identification we could find.

Need full roller assembly Thanks

I could really use the help as soon as possible. Thank you in advance.

I'm in search of 2 rollers for a 1972 patio door. Attached are photos of current rollers. Are you able to identify a workable replacement? Any help would be greatly appreciated.

I have two sliding glass patio doors with roller assemblies that need to be replaced, but i have been unable to locate any information on them or the door. The doors might be custom made replacements for the originals.The roller assemblies are fit into an aluminum extrusion inside the door frame, ra ... (cont.)

Looking for 2 replacement roller wheels with housing for a bottom roller drive thru window. No brand marking was on the frame. I appreciate any input on this part. Thank you

I've looked on several sites cannot find single roller assemblies for a herculite k door maybe you can help me out

Hello, I have a sliding patio door from the 60?s. The picture attached is if one of the rollers. As you can see, it has worn out to the point the door cannot be used. I don?t want to replace the door, but cannot find a replacement part. I have tried to alter rollers that I have gotten at Home D ... (cont.)

Hi, See attached pictures, would you happen to know the make and part number? Do you have any laying around? The house was built in the late 70's. The doors are metal frame patio sliders. Thanks, appreciate any help you could offer.... Derrick

Hello - My patio door rollers, 81-002, arrived yesterday, however, I can't get them to fit my door. The quality is much better than the original rollers, but, the unit won't slide into the extruded aluminum door frame grooves. Attached are the dimensions of the existing roller. Do you have 2 ... (cont.)

I just removed these rollers from my aluminum sliding door. I don't see a good match from your photos. They are held in place in the door by a roll pin. The rollers are 1" OD in their groove. They fit into a slot that is 1/2" wide. The axle is a 1/4" roll pin. If you don't have a match for the ... (cont.)