Viewing all customer Discussions for:

81-129 Diecast Roller, 1-1/2" wheel

Need to know if you still have these in stock or can rollers be replaced

I need two replacment rollers. 1.25 in roller .25 x .885 axle that rides in door frame.The carrier that holds the roller is .660 wide x 1.875 long from screw case to center of axle.Maybe an upgraded assembly is available that is not aluminum. Thanks, Bill

Hi, I need to replace the rollers shown in the attached picture for 18 sliding glass doors for a total of 72 rollers (one set of rollers is duplicated). The original hardware shown comes from a 1962 home and only marking found were the name "KILIAN"

Looking for this roller for a sliding glass door.

Doors installed in 1984 and the single roller mechanism is broken. I cannot find the single roller unit anywhere and need 4 of them. Please help. The wheel is 1 1/4 inch. the length of the unit that attaches to the door frame is 1.5 inch from the hole to the edge.I do need 4 of these. ... (cont.)

I'm looking for replacement roller for attached photo it looks like 81-002 the tapped hole is 1 13/32 from non roller end also track is worn what replacement track do you recommend and how is track mounted door is marked national windows if that helps.Thanks for your consideration Mark ... (cont.)

hi, we are looking for 4 replacement rollers for an older slidig door. is there a way to send a photo to see if you have it in stock? we have attached a photo in case you can help with the photo.

Have an old slider from early 60"s measurements kilian name on roller, syracuse, ny 1 5/8 inch diameter roller assembly 2 pieces adjustment piece 1 7/8 inch roller and assembly together 2 7/8 inch 2 1/4 inch without roller 1 1/2 assembly togeter 13/16 thickness or depth

The roller assembly from my exterior sliding door is broken. I was replacing the wheel when one arm of the assembly itself broke. The door is also designed to have the screen on the interior and the lift out door on the outside if that makes a difference. Can you please tell me if this part is avail ... (cont.)

So I am trying to replace the rollers on my sliding glass doors. Upon removing them I noticed two different pieces. The one on the left was missing a wheel and the one on the right looks like a hack job because i got replacements that looked like the one on the right and they don't seem to fit. I wi ... (cont.)

4 panel aluminum sliding door with 2 outside stationary panels need rollers track covers and weather stripping. Thanks

This roller is original to the sliding glass door from our home built in 1976. When the roller is laid down flat on it's side (as shown in photo #003) the length is approx. 2 3/4 inches and the height is approx. 3/4"

Good afternoon! Hoping you can help by letting us know if it is possible to find a roller assembly like this one. Think the door was bought back in 1970's. The width is about 3/4 inch, probably looking for a needle in a hay stack, but will be easier if I can find a replacement. If you think yo ... (cont.)

Hello, I need to replace both of my sliding glass door rollers. I think I have provided good pictures with measurements, the only other thing is that the wheel is 1 and 1/4 inch outside diameter. There are no markers on the rollers, and none on the door unfortunately. Can you help me find ... (cont.)

Howdy I'm going to replace rollers on a patio door on a 1978 fleet wood mobile home. It looks to me like the rollers in place are not close to original equipment.. I,m looking at 81-129 or 81-262 Which one do you recommend ???I,m a new customer and would like a reply soon so I can place my order ... (cont.)

Looking for parts replacement, these are from a heavy sliding glass door. Unable to find at local hardware store, please help. Thank You

Looking for glass door rollers for 1970's aluminum glass doors. I have attached pictures with the cap from a soda bottle for scale.

Hi there, I've seen some great discussion on the board and hope someone could me out with some sliding door rollers. I have a contemporary house built in 1972 with Allen Stevens doors and windows, and the rollers on a 8 foot wide (4' doors) door failed many years ago. They are clearly marked with ... (cont.)

The wheels are toast. I get a pretty good workout opening and closing it. I cannot see any numbers or markings on them.

need sliding door replacement