Viewing all customer Discussions for:

87-058 Window Roller BB Wheel, 9/16" dia.

Hello. I am seeking a replacement window roller assembly. Attached are four images. The plastic assembly is 2 3/8" long, approx 5/8" high, and 1 11/16" wide. The metal roller is your part number 87-058 - Window Roller BB Wheel, 9/16" dia. I do not know the brand of the windows but can provide pic ... (cont.)

We ordered the 9/16" wheel and it's a bit wide for our assembly? Any other sizes available?

You have lots of items that are close and may likely work ...so here we go.I have included 5 pictures. The Outside diameter of the flat brass roller is 9/16".The pin (.172") that holds the roller is worn along with the elongated hole in the roller. As a result, the rollers are recessed and the slide ... (cont.)

dimensions are: 5/8in wide 2 1/2in long 1/4in deep Certainteed window

?This is a rusted wheel. 5/8 diameter, flat wheel (not concave). 3/16 spindle. Do you have these? Without pulling the window out again I can say that the wheel spindle just snaps into place, it looks similar to your product 87-111. The metal wheel itself is about 7/32 inches wide. If the spindle is ... (cont.)

this is a brass roller 1/2: in wide

9/16" diameter roller 3/8" wide with an axle 3/8" in diameter that protrudes on each side 3/16"Oh, I need 4 of these rollers.Thanks for your help.Bob

I need whole or roll only. If you have a role with bearing will be perfect. Thank you

I need replacement rollers for the window in a new to us house that I do not know the manufacturer of. PFA images of one of the rollers I was able to remove from the frame. The bodies are OK, the brass wheels were not cleaned, got stuck, and have flat spots worn on them. Full replacment or replaceme ... (cont.)

Trying to find replacement rollers. Unknown make of windows. No #'s. Uses a brass roller . If a unit with the same measurements on the brass wheel is available I could snap them (2 needed) out and into my existing frame. **see photo for dimensions** Thanks, Terry

Looking to improve the slide action of my windows that move on two sets of rollers set in a plastic housing at the bottom of the frame. No visible identification markings on the part or window or frame. Aside from replacing the rollers that are damaged or missing, can just the wheels be replaced ( ... (cont.)

I just bought a house a few blocks from the ocean and most of my slider window rollers have corroded to nothing. Do you know where I can buy replacement assemblies or it appears the roller and axel snaps out. Thanks p.s. there are no manufacturer markings on windows or rollers. Thanks ... (cont.)

The manufacturer of my windows is Certainteed, I would like to purchase the full roller assembly or the wheels only.length - 2.150 incheswidth - 0.595 inchedwheel diameter - 1/2 inchwheel width - 5/16 inchaxel diameter - 3/16 inchaxel length - 1/2 inchscrew holes - 1 inch on center ... (cont.)

https://www.swisco.com/Sliding-Window-Roller/pd/Sliding-Window-Rollers-With-Plastic-Housing/87-143 Maintenance says they need the larger wheel that fits into the part referenced above. What is the wheel part number? Thank you!

I am looking for whole wheel carriers, or brass wheels and axles. PTG sliding windows. Roller is flat face brass as is the axle the diagram I'm sending you is the closest I can find to the actual size

Need to replace the wheels that roll on the track of the window frame.

Need 12 pcs. The window is aluminum sliding window I do not have any name or number to give you. Do you have anything that looks like this

Looking to replace wheels in Acorn slider windows. The bracket assembly is still good in most of the windows. I have used the 87-061 assemblies and sometimes just pop out the wheel to use in the old bracket. It is an easy repair without breaking down the window frame. Is the 5/8 roller wheel av ... (cont.)

Name on latch: Prime windo part is 21/32" wide. End piece us 7/8' high and 15/16" wide. Body of piece is 11/16" high, not including roller. All nylon, flat roller. Screw hole is 3/4" from base of end piece.

I need a window roller assembly and the bottom rail is damaged