Viewing all customer Discussions for:

95-140 Tilt Corner Key, 3/16" x 3/16"

Good Morning. My name is Joe and I'm looking for 2 different storm window corners. Attached are photos, including measurements, of the two corners. I have not been able to find them online as of yet and was hoping you could help me. Thanks in advance.

Good morning: I have a have a sliding window on my front storm door. The top right corner has separated from the right hand side of the aluminum frame which surrounds the glass of the window. the pivot has broken which joins the top and right sides of the aluminum frame of the sliding window. could ... (cont.)

Please identify these for me. Thanks!Greg

Hello: My storm window has a little round cyclinder that holds the upper edge of window in the aluminum track. It has a number on it, "200-910". It matches closely to your 95-193 where the 3 dimensions as shown match exactly. However, the flat rectangular pad shown on your picture is not on my par ... (cont.)

I'm looking for a match for my mobile home window corners. The picture is of 2 separate corners. Each one has a different piece missing. One has the tilt pin missing, the other one has a portion of it missing that goes into the frame itself. Can anyone please tell me what part they closely match. Th ... (cont.)

Looking to replace 2 top corner brackets which have lost the tang which keeps it in the frame track. Additional photos are for aid in identifying purposes.

My glass storm windows (Benada) are screwed together at corners. Top tilt is nylon/plastic and has hole for screw that fixes it in place. It is 3/16 x 3/16 x 1 1/2 (including 1/4 tilt insert)I have located other parts on your site (91-090, 95-016, 95-00995-008) that seem to fit Although my screen ti ... (cont.)

Looking for this part as it also helps hol screen in track. Ty much for helping.

I am looking for zinc die cast corner keys, top tilts, and left and right spring latches for extruded aluminum triple track storm window repair. Attached are photos showing corners of screen. Please let me know if you can supply the correct parts.

Need a replacement corner latch.

Need help identifing this corner swivel key. Used in RV window on LCI 3-season doors.Mark

Latch set for storm door, window. No numbers or markings like there were on the corner pieces. The pivot corners appear to be your 95-140. Also need the associated corner piece as above but without the pivot pin.

Hello, I'm unable to find a match to this Fox Weldor storm door screen frame corner David

latching 36" wide storm window on a colonial house. Currently 35 yr old plastic. Windows mfg by possibly "Solaire " not sure. About 23 sets are needed.

Hello. I need to order 8 replacement keys for my window screens as I lost the clips. Unknown manufacturer and model. Can you please help me identify what part to order? Thank you.

Sent from my iPhone

I would like to purchase if you have them the top and bottom corner keys for an older Larson storm door top sliding window frame. They are very similar to the 95-140 and the 95-002

one of these corners is 1-1/2 inches north to south and 1 5/8 inches east to west. With a width of 1/4 inch. The other corner is 1-3/8 by 1-3/8 inch With a width of 3/16 inch. A Swisco rep suggested that I purchase 95?016 for replacements However they are too thin and don't catch inside the slides. ... (cont.)

Dear Swisco, I need some parts to repair old storm windows. Image 8726 shows a right and left slide bolt to be replaced. If you have them I would like three right and three left. Measurements are: total length= 3 5/8 in; Body Height=3/4 in, Body depth thickness = 7/32, Nose length= 1 in, Nose Height ... (cont.)

We have a Larson full view storm door, with a retractable screen on the top half of the door. We need replacement parts for the item pictured (the left side clip is what is needed). We had ordered part #95-191 (4 qty), order #1939195 which does not appear to be the correct part. Can you assist iden ... (cont.)