Viewing all customer Discussions for:

95-182 Sears Tilt Pivot

As we tried to slide the lower glass panel in our storm door (manufacturer unknown) the pins at the top of the panel snapped as seen on the photos and the glass panel fell out. I'm having a dickens of a time finding a replacement.

I'd like to find the whole window panel but you don't seem to sell those. A few pieces that held the window in had broken and the window fell out of the door, getting bent on one corner. I am attempting to bend it closely enough back into shape and replace this white part, 2 springs and one of the l ... (cont.)

Do you carry this piece? The end piece has broken off but it was round.

i have a storm door with a window that you can slide up and down. see the attached pictures. on the window that slides up and down, there is a plastic "pin" that is attached to the window and the pin is in the window track. that pin broke and i'm having a hard time finding a replacement. Can you ... (cont.)

Not sure what this part is called but it holds the glass in the frame track. There is no name or writing anywhere on the storm window. All I have is the attached photos. Thanks for taking a look at this.

It's a little plastic tab with what looks like a small screw or tension coil. The windows tilt kind of sideways and you pull them out. I attached a picture of one on an intact (but dirty, sorry) window showing the tab that's missing. It's just on the upper part of the window. Could I please get h ... (cont.)

The part on the table next to the window is the broken one. The corner of the window shows the other one in place.

Installed in the top corners of a removable storm door window. The plastic 'cylinder' slides within vertical tracks one either side of the door's window frame. Looking for a replacment for a broken part.

Parts and windows at least 40byears old. They are dual track. These sliders/guides are brittle and break when opening and closing the windows.

The part in the photo is from a storm door -- I think it is a Larson. There is no identifying tag on the door. The part is stamped with the number 8232. It is used at the top of a storm door glass panel to slide it into a track and hold it in place. The door has 3 panels -- two glass and one scr ... (cont.)

I think this might be a prism simonton door but not sure.

See photos...I need pricing on the bulk oarts

We have an older aluminum storm door on our rental property. The small plastic pins in the top rail that keep the window in the frame broke. I am having trouble identifying the name of the piece or where I can buy replacements. Any help would be appreciated

frame is 5/16 thick. There are what look like 95-182 in the upper corners. Do you have these latches? There are also middle pins along the sides that look like the upper corner plastic pins. Do you have those?

We are in need of this pictured patch for a storm door window that slides up and down to reveal the screen part Of the door The white part is top of the right side of the window that rides in the channel of the window. Has a screen that goes through it to anchor it The metal piece with the spring ... (cont.)

Looking for replacement clip/pivot corner for storm window on screen door. Only info I could find is from the attached sticker on the door. Thanks in advance

Hello ! I need assistance findind parts for our screen door.Sugarcreek Industries Door # 399 self storingRequesting quote4 each screen door finger latch die castand4 each window Guide white partThanksRobert

Hello, We have numerous of these small white pieces that hold in the storm windows and allow both too and bottom to slide up and down. We have 4 of these doors. I'm sorry that I don't know what they're called to further help. I've also enclosed the only tag that could be found on these storm door ... (cont.)

I am looking to replace the channel balances in my windows. There is the number 2410 A stamped on the channel. As you can see the channel is 24 1/2" long and 5/8" wide. If you can get back to me on a price and availability I would appreciate it. Thank you Pat

Replace broken metal cllps to storm window on storm door with one i brought from your company. Need to replace plastic unknown items pictured above. They were removed from trim section at top of window. Those are photos showing the top with looks like im missing screws to secure frame on the inside ... (cont.)