Viewing all customer Discussions for:

32-088 Drawer Guide

I have the part which you say matches your 32-088. I need several drawer track guides which measure about 2 1/2 inches wide and1 5/8 inches from the highest point to the bottom. The part was manufactured by Hardware Designers, Inc. and has the number 452 USA on it. The slide opening is 1 1/4 inch ... (cont.)

Hi, I have an old tanker desk that has damaged guides. There are no markings on the desk to indicate the manufacturer. I have included a picture of one of the drawers, a picture that shows how the two guides are mounted on the drawers, and a close-up of one of the guides. I'm calling this a t ... (cont.)

what screws will i need for this product and for the other pieces that concern it.

Not sure which is the one i need, bottom of opening looks like 1"-1/4"

Need to order this part

Hi, The original was made by Hardware Designers of NC. It was about 48 years ago. I took the picture of the best looking one of the 5 drawers. Sure hope you can help me. Thank you, Walter

are the r-22 still available

Drawer pull #32-122 is not correct for our need. The dimensions are somewhat different. The old one is numbered #452 from Hardware Designers. glide width 1 9/16" - total width 2 1/2" glide height 3/16" screwhole from top of glide space 3/4", from bottom 1/2", from outside edge 3/8" ... (cont.)

Hi! No luck in big box nor smaller hardware/furniture/appliance stores. This one is off the back of a kitchen drawer. It has a single center guide on top as opposed to two on the sides plus some sort of wheel (think Ikea). The part is without any markings, stamps or numbers. It is 2 1/2" wide by 1 ... (cont.)

Hi, I'm looking for a drawer track glide that approximately matches the dimensions in the attached pic. I also need a rear mount socket that would fit the same slide. This is for a drawer that has a single slide on the bottom. If you don't have the parts I need, do you carry single slide kits fo ... (cont.)

Looks like a number of people were interested in replacing #452 guide with a similar part from your portfolio. Any good matches?

I am looking for a part the holds the front of the drawer guide on, The Rear socket I use is #32-009 & the drawer guide is #32-088. What part would hold on the tapered down front of the guide.

This is a photo of a rear drawer guide I need 12 of them the best I can come up with is 2 1/2 wide 2 3/8 rail size 1/4 rail opening it resembles part 32-031 can you help Me with this

Looking for this part

embossed in plastic: Hardware Designers Inc. #452 USA width: 2 1/2" depth: including "teeth" 1 3/4" widest distance between "teeth" (width of rail) 1 1/4" screws: 1 3/4" apart on center drawer back thickness: 7/16" to 1/2" (screws?) I would like to order 10 glides + screws. Thank you Sharo ... (cont.)

Part Needed: Plastic Drawer Slide Mfg. ID Raised Lettered -- "Hardware Designer Inc. #452 (1) Oval Shaped adjustable screw slot - top - centered. (2) Additional screw holes -- Each 3/8ths in from each side. "Mouth" = 1-3/4in. wide. Richard

I have a plastic drawer slide which identifies as the following: R FISS MFG Corp NNC PAT: 2855260 PAT: 2857233 DO have this part? Thank you very much

please let me know if you have this bracket. thank you

Hello, The house we bought has center-mount drawer slides with a central metal channel attached to the cabinet, rollers on both sides of the cabinet opening that the drawer sides roll on, and a white plastic glide screwed to the back of the drawer. Most of them work just fine, but a few of the pla ... (cont.)

Do you have the part with the dimensions pictured?