Viewing all customer Discussions for:

32-089 Drawer Track Back Plate, Pair

This part is smaller than my rail "C" What part number do I need for a one inch rail? Thank you, Norm

Looking for rear draw slide bracket for a vanity - the side is 4 x 1 3/4 with a one inch wide channel to hold the slide - screws are extra wide and built in to plastic

Just received the 2 rear plastic brackets 32-140 but I forgot to check the measurement of the inside fixed rail guide. My rail needs a 1" slide instead of the 15/16" of the 32-140. What should I have ordered instead?

What size rail does it hold?

The left rear mounting socket cracked on a kitchen drawer - it is heavy white plastic. The glide is a Mepla MR2031/550. The brackets I have been able to find that fit the glide unfortunately do not line up with the existing holes in the cabinet back. The broken bracket measures: 1 1/4" across the ... (cont.)

I have some older Quaker Made Cabinets. The rear sockets for the drawers have failed in a couple of them. The only markings are an R and L on the brackets. The slots measure approximately 1 inch by 3/8 inch. Attached are pictures of the right socket and a left and right one installed. ... (cont.)

I need 4 drawer track back plates that will fit guides with cross sectional dimensions shown in the photo. I purchased product code 32-089 a while ago, but the 3/8" dimension of those plates is not quite wide enough. Do you have any plates with 7/16" or 1/2" cross sectional width? ... (cont.)

i need rear drawer slide holder (these cabinets are schrock and they are over 30 years old) 1/4 wide x 3 3/4 long and 1 1/4 tall. the drawer slide fits into the rear of the holder and helps hold the drawer.

From the dresser in my 1995 Thor RV broken Looks close to # 32-139 but not exactly Base dimensions 2 3/8x1 Slide dimensions 2 3/8 long x 1 (inside)

What is the opening on your back plate 32-014. My old backplate has a 1 inch opening for the rail to fit into. Or do you have a different one that would work. It looks like I am going to have to replace all the backplates because one at a time they are breaking. thank you

Hello! I'm in need of two sliding drawer sockets and your site popped up when I did a Google search and I'm hoping you can help. I've attached four images of the socket. It measures 4 1/4 inches long and it looks like the part where the little wheel slides into is a 1 inch opening. Thanks for an ... (cont.)

According to Hettich their old part number for this was 9004739. The left was 9004737. These parts are no longer available from them. The opening is about 1 inch. The length is 4 inches. The back (with screw holes) is approximately 1 3/16 width and 1 7/8 height.

Based on my measurements, and your user friendly site, this appears to be a 32-809. Seem to be no markings other than R and L. Appreciate your web site...clear photographs & measurements.

I need replacement rear drawer slides for a Ferrari vanity. The only identification on them is L 1-2 and2-3 R.

I have a cracked kitchen draw bracket made by "Ferrari Lecco - Italy #B023", as stamped on the bracket. Looking to buy two sets of the brackets. Opening width is 3/8" by 7/8" height - Length from the back plate to the front of the bracket is 4 1/4". Can you help me out. Sincerely, Steve ... (cont.)

Are these compatible with all slides. I can?t seem to find replacements because my cabinets are 9 years old. I looked on all sites and do not see the ones that I have. Are there any that are compatible with all drawers?

KV 1284-3

Hello, I have a couple of plastic rear track mounting brackets that broke and I am looking for possible replacement parts. These plug into holes into the thin back plane of my bathroom counter, so trying to drill into them in not a good option. Any thoughts? Thanks!

G 6020-6 Rh and Lh

Looking for rear slide mounting bracket. They were installed in early nineties.The rear hanger at the base is 1'' 1/4 wide2" long Were the slide slips into hanger is 3 1/2" long Thank you Ron