Viewing all customer Discussions for:

32-119 Grass Adapter Bracket Pair

Trying to locate replacement parts for these broken pieces on kitchen drawer. Do you recognize these?

Back of cabinet to secure drawer slide.

I need a set of new slided for my draw, but I am not a cabinet expert and need some help identifying what type of slides I need to order. Perhaps I could send you some photos if my description is not that good. The back is held in place with a plastic mount and the rails measure I think 22 7/16 bu ... (cont.)

I need 2 different types of drawer rail brackets to fix some drawers.

Greetings and thanks for looking at this part for me. I have other pics if needed. Since these parts are almost 20 years old, I think it would be best to replace both the right and left brackets. Also I want to get 3 pairs total - to have for future needs. Thank you. Most Sincerely, Brenda ... (cont.)

I have a Yorktowne kitchen cabinet (~25 years old) which has five drawers withUNIGRASS 6600 drawer glides installed (side-mounted). Recently, one of the plastic rear support fittings failed (probably fatigue fracture). The drawers are 20 inches long. The stationary glide is 22.5 inches long.In my we ... (cont.)

A few years back you received queries about replacing a plastic slide connector used by Scheicher in their cabinets. (Here's an example of one: https://www.swisco.com/discussions/scheirich-kitchen-drawer-parts-77-68729) You didn't have an exact replacement part then, but I'm curious whether anything ... (cont.)

I'm not able to find the right replacement for this. It looks like a G 360C or a G 60c on the part. It's about 2 1/8" L x 1" W x 2" H

I need to repalce 3 Rear Mounting Brackets for a PMI-CM565R Drawer slide. The dimension of the drawer slide and bracket recepticle is 7/8". I have been to several Hardware and Big Box stores and although their brackets list a dimension of 7/8" they were all to small, approximately 13/16". Can you ... (cont.)

Any idea what to replace these with? the glide support fits into a slot and then that fits into a support using 2 plugs and the support is screwed into the wood from the side.

Plastic, does not screw in, metal piece pops into it. Scheirich drawer.

Hi We are still a year out on replacing the kitchen and the current brackets keep braking Do you carry these oor something that would work. The brackets that hold the rail are 1.25 inch

Swisco Help,I have attached 3 photos. I have a plastic bracket for a kitchen drawer that has broken. I cannot tell you who the rail and bracket hardware was made by. I do not see any identifying information on the rail nor the plastic bracket which identifies the manufacturer. I see the letter " ... (cont.)

Measures From back of boot to the front 2 10/16 Width of base is 1 5/16

I have 4 broken brackets on two drawers. The only markings I have been able to find is a "G" on the rivet that holds the roller in place. There is "RC" stamped on glide on right and "LC" stamped on left glide. The glides are 22" long. The roller has a diameter of 3/4". Glide is angled at the end and ... (cont.)

The piece that holds the slide on a kitchen drawer was two pieces of plastic. The on on the right rear broke.

The slide had UNIGRASS6600 imprinted on it. The plastic mount is broke. Here is a photo of a non-broke mount, which I need.

Please help me find a replacement part that works easily

The yellow piece broke for the long bar to slide into. The square yellow piece is mounted into the wall. Do you know what it is called and where I can get one from? You help is greatly appreciate it very much. If you need more explanation, please do not hesitated in reaching out to me. Thanks, Lou ... (cont.)

Tan bracket for kitchen drawer only have a number 3 in a circle