Viewing all customer Discussions for:

32-119 Grass Adapter Bracket Pair

This is the right drawer slide bracket. Do not know brand.

Hi, looking for the above. track is 1 inch wide (see pic of track) Hope you can help.

Like looking for a needle in a haystack lol...trying to find a replacement for that "L" shaped chunk of plastic in the pic (this an intact one I removed to find a match). Open to new slides, BUT on the old one..it has a tab to screw into the back-face (back of the front?) of drawer. Hard to describe ... (cont.)

Hi there - looking for 2 pairs of replacement parts for some Yorktowne cabinets that are probably 25+ years old. The drawer back plate are broken on one set and thought i should replace the other set in the cabinet. The photo is for the working set. The rail appears to be an 1" in height and the ove ... (cont.)

Hi, what size screw (or other fastener) do you recommend to best fit the 32-119 Grass Adapter Bracket? Thanks, Adrian

Rear drawer brackets in kitchen cabinets. G 6020-6. Need replacement parts in a home built 1986.

Need to know where to purchase. I am in Des Moines iowa

Looking for a replacement drawer guide boot for a 1980s Scheirich cabinet. This is the plastic piece shown at the bottom of the picture. It is used to connect the cabinet slide (shown in top of picture) to a metal piece in the back of the cabinet (shown in the middle of the picture). The plastic ... (cont.)

I'm looking for a replacement part. It is for a Merrilat kitchen drawer. I believe it's called an end bracket where the sliding piece goes into. 1" wide on inside, requires no screws, about 2" long. Do you carry this or something that would work?

Need the broken piece that supports the slide for the drawer slide mechanism. It snaps into a metal bracket in the back of the cabinet.

Hi! I'm looking for replacement parts. It's for a slide system for a roll out tray. We have a tall cabinet from Merilatt installed in 1990. I need the anchors that hold the rail to to the back of the cabinet. The rail itself is 23 inches long. I sure hope you can help me.Thanks,Frank ... (cont.)

White bracket for a glide for a drawer has on it a G 6600 mounting site approx 1.25 wide x 2.25 long length approximately 2.25 opening width approximately 7/8" high and approximately 3/8"wide for slide area

This teflon piece holds the slider for my kitchen drawer and it has broken. How can I replace with a new one? Do you have a new one for me and can you tell me how to get the old, broken one off the back wall of the cabinet. I can't figure out how to remove it or how it was installed. ... (cont.)

rear drawer socket for unigrass 6600 slide. You recommend 32-018 rear drawer socket. other comments and the photo show a straight socket. the broken ones are slanted but do not have a product number. John

Looking for the replacement. Plastic or metal

Any ideas for a replacement support. No markings on them or track. Track is 1 in x 3/8 in. Support wraps around a 3/4in board. These are bottom mount tracks. Hopefully you can help Jeff Erb

I need to replace this side mounted drawer slide socket that recently broke. The socket has the markings as follows: "G* 6600". As seen in one image I uploaded, the slider assembly is about 22-1.2 inches long. The other end of the slider in this picture is mounted flush to the back of the drawe ... (cont.)

The plastic piece broke on the rear of the drawer track holder. This is on the right side of the drawer that is actually mounted to the back of the cabinet. I need a replacement piece so I can put the drawer back in place. Any help would be great thank you

Hello! I'm looking for a replacement part for the back drawer mount. Rails have Unigrams 6600 stamped on them but I don't what the exact model number is. This piece is 30 years old so I'm positive there's a different part I need to replace it with, I just can't figure what it is. Any help woul ... (cont.)

HI, I am looking to replace this piece x2. They fit at the back of the drawer. I saw the number PPW092 in the back plate on the back wall of the cabinet. Hope you can help!