Viewing all customer Discussions for:

32-119 Grass Adapter Bracket Pair

This drawer slide is a Grass America brand. The installed photo is the left bracket but the right is the broken one. The G* and "RC" are stamped on the slide itself. No markings on the bracket other than "right" The house was built in the 80s so that may give you a timeline.

We need just the plastic end brackets... they have cracked so the drawer keeps slipping off the track...

Looking for part for drawer.

I am looking to purchase about 34 of the plastic mounts at the end of the rail

L bracket for a drawer slide.

Do you have a replacement for this guide boot?

No markings on anything except L and R. Cannot match dimensions to anything I find online. Overall dimensions are: 2.5" H x 1.5" W x 3" L. Channel outside dimensions are: 1.2" H x 0.5" W. Channel inside dimensions are: 1" H x 0.4" W.

Came home to find the utility drawer hanging at a 45 degree angle. The culprit is this rear track bracket which had cracked in half. The drawer slide (the part attached to the drawer itself) reads "Unigrass 6600". No markings on the bracket other than "Left" and "Right". Dimensions for the openi ... (cont.)

The nob on the back of my drawer slider bracket snapped off. I do not have a picture of this bracket. The measurements are very close to these figures: nob to front-1 15/16", inside opening: top to bottom-15/16", top width-7/16", bottom width-5/16". I've looked all over for this and can not find ... (cont.)

I am looking for a rear cabinet mounting bracket the one I have is a white the the plastic peice measures 1inch x 2 1/4 inches .any of your products match these dimensions ?.the one inch is where the roller rides on .I have been looking for this type of part for 2 years I'm glad I found your site bu ... (cont.)

I need a few cabinet drawer slider brackets. These fit in the back of the cabinet and support the slider track. I have attached picture for you. Please see if you have these or something that will work and I will get back to you on how many I need.

I need a replacement for this piece. I'm sure it's no longer manufactured so I need one that will work from your catalog.

Parts for UNIGRASS 6600 sliding drawer: part 1: 1 white round rubber spacer and part 2: 1 rear mounting bracket plastic white

Looking to find new socket to replace broken one

Greetings. I just received my product code 32-119 Grass adapter bracket kits. They will work with my drawer slide(s) except one. I noticed that one slide is straight on the end that goes into the adapter bracket. Apparently this one was replaced at some point and was not installed as a pair. The oth ... (cont.)

The drawer slide (image drawerslide4) keeps coming off the plastic rear drawer socket. I believe I used part #32-003 or 32-005. How can I keep the drawer slide. Is there anything deeper to secure it better? What else can I do? Would it be better to just get new hardware? Thank you for any ideas. The ... (cont.)

This is the picture of the track. I need the back guide. It has to be at least one inch that the track would fit into. Thank you so much for your help.

this is a two part bracket first part number is h-104 that I can find second part that is broken is part# h1043 wich slides into h104 supports a glide for a trash can cardell was the cabinet company

Hi- My kitchen drawers are made with Unigrass 6000 epoxy coated slides. The drawer side has the slide integrated into it. The attached photos show the uninstalled cabinet slide, the broken (right side) part that I need to replace and the unbroken left side installed. The cabinets were built ... (cont.)

One side of our top cabinet drawer has broke. Need to replace. I order 32-012 but it is 3/8" to 1/2" too long. Also, the back side of the broken piece looks to be glued to cabinet back, not screwed in. Any ideas how to take the old piece off when replacing with new?