Viewing all customer Discussions for:

32-119 Grass Adapter Bracket Pair

Do you have one that is a 1/4 inch wider for where the shelfing bar is slid in and being held in the plastic sleeve?

Builder grade kitchen drawer cabinet side glider. Only identification G. LC See attached photos

inside measurements of item 32-119 and item 32-108 rear drawer guides.

Good Day Good People, I am in desperate need of 12 of these beige color plastic bathroom drawer brackets. I can fix with just 4, but I would like to have some spares if needed in the future. The only number I can find out of all the bracketery, is the patent number on the metal bracket t ... (cont.)

Cannot find the drawer slide locket that is in the photos .

Looking for replacement rear receiver brackets like the one shown here. The guides on both the drawer and the cabinet do not have any names/codes that I can see. The guide that goes into this bracket is about 1

Do you have a replacement part for this? Thank you

Hi folks - The hardware in my twenty year old kitchen cabinets is beginning to fail. The plastic brackets which attaches to the back inner wall of the cabinet and holds the sliding shelf rails are failing. The metal side rail is labeled "Unigrass 6600". Do you sell replacement parts? ... (cont.)

Hello, I work for a lumber yard out of Dubuque Iowa and we are trying to locate the above attached drawer boots. We are only in need of 6 of them, but would appreciate any help you could give us? Please let us know if you have any questions that would help locate the items...

Door rail back piece

was looking for a drawer side socket similar to the 32-119. The one I need to replace has an attached dowel that attaches the drawer socket to a metal plate that goes across the back of the cabinet. Since the hole for the dowel is at the bottom of the plate, I'm concerned that the 32-119 might hang ... (cont.)

Hello. I am looking for a replacement part for an existing kitchen drawer assembly. I don't have much information on the assembly, as I did not install it. But it should be pretty straight forward: I am looking for the rear L bracket that the drawer roller guide rests in. This L bracket screws into ... (cont.)

Looking for socket possibly by Merillat. Says Unigrass 6600 on the rail. Some say they use the Knape & Voqt part 1805-101WP as a replacement. Is this OK? What works best for these socket replacements? It looks similar to the Swisco 220X200 & 493X317....not sure what this means. Our hou ... (cont.)

Hey I was hoping you might be able to help me. I have a bracket that holds the rails for my kitchen drawer. The company is Marsh, do you carry these parts?

Hello, I have a 91 year old step dad living in a mobile home here on my property in Hope, Arkansas. I am in need of some Wesco-Fastec cabinet drawer end sockets to repair his kitchen cabinet drawer slides. A picture of the end sockets is attached and need 6 of each, left & right sides. Contact ... (cont.)

Have a two inch wide drawer slide. Need a socket. Plastic one currently is broken, they are side sockets.

Our Kitchen has 14 drawers with Swisco drawer slides and brackets (PN 6600). See attached photo. 6 of the drawers have broken rear brackets. How can I get them replaced? Thanks, Mike

I can barely read on the rail itself that this is a Grass 6600 system. I couldn't find on line a rear rail holder that had the dowels on them. If they are available that is what I need. If not I can use a screw in bracket, but I want to make sure I get the right size. I'm going to get 2 right and 2 ... (cont.)

Hello, Would you know if these are still available. I think they were for Schrock brand drawer glides?

Hello! inside of rail measurement is: 1" height is: 2-1/16" tall length of rail (from outside back of part)is: 2-1/4" width is: 1-1/4" "G" on upper left on back of "R" part. "R" is surrounded by a circle. "G"on upper right on back of "L" part. "L" is surrounded by a circle.