Viewing all customer Discussions for:

26-121 RH Top Tilt Latch, 2-1/8"

No numbers or markings on existing latch

There are no markings I can find on the windows. even looked on the spacer. Know the corners are NOT welded. :( Any information about the windows and parts that are available will be appreciated. Thanks in advance.

The first picture is a tilt latch 3" long. Everything I saw on your web site is less than 3". Second picture is a nylon insert that the screw holding the top of the spiral balance goes into. Can't find it anywhere.

I don't have a name or anything I am looking for 7 of these for each direction. Any thoughts that you can identify these? Jesse

Hi The moving piece inside is broken, I should buy both right and left. There are no markings on the window or on the latch 3 1/8" x 1 3/8 " 1/4" thick 2 1/8" between holes while plastic it is screwed on top of the frame, it is not recessed into the frame (I would like the same bec ... (cont.)

Hi! I have to replace several sets of these in my home before i can sell it. The windows were installed in 1999, before we purchased the home. The company which installed the windows seems to have gone out of business, and no one local has any latches that will fit. The dimensions of the piece pi ... (cont.)

I bought some replacement latches but the part that retracts is too short to extend into the frame. The old latch shown on the left is 3 1/8 x 1 3/8. Please give me the dimensions of the length of the part that retracts so I can be sure it will work. The section that extends is 1/2" The existin ... (cont.)

Need help replacing my latches in my home. I hope the pic helps. Some of your products look close but I cant find an exact match. Any help would be great. Thanks Lance

white vinyl 3 1/4" lenght 1 1/4" width 1/2" lock 1 1/4 between screw holes number on latch 11148 Thank you

Hi, I need to replace a few window latches that have broken. The dimensions are as follows: 2-1/8 inch attachment screw holes 3/4 inch from screw hole to end of casting (not including sliding latch) width is 1-3/8 inch thickness is 5/16 inch Based on your site, I see either the 26-120/12 ... (cont.)

Hi guys, I need surface release replacement mounts for Traco double hung windows series TR 4300; I took a picture of label,can mail it if needed but,rest of it goes as follows; 851771 062503 202-008 I appreciate your help and would like to order parts if you have them ASAP

I needed to replace a few broken latches on windows I had installed 17 years ago. The SWISCO website was very helpful in matching the parts needed. The cost and shipping was very reasonable. This was a very small purchase but on another company's website, the cost would have been three times as mu ... (cont.)

Need at least 3 pr. of window latches. Not the locks but the plastic latches that snap into the jamb. I was told i need 26-121 R and 26-120 L Can you help me out? Thanks! Steve

Would like to see if this hardware is still available. If so would you contact. Would need a quote for the following: 108qty of 21" prod code S600-21 50 qty of the tilt latches "see picture" I couldn't find this on your website but the deminsions are 2 1/8 on center screw holes/ 54 qty o ... (cont.)

I have a right and left lock that needs to be replaced-- but I keep pulling up your images and nothing seems to match what I am looking for could you please help-- thanks the overall size is 3 1/4 inch long x 1 3/8 in wide from the one screw hole to the other is 2 1/6 From the one screw hole t ... (cont.)

26-121 Top Tilt Latch, RH - referred by a past superseal window seller..superseal no longer makes these windows. I desperately need replacement top tilt latches. Thanks so much for your help. Kim S.

Here are a couple photos of my latch.

is this latch spring loaded?

What is the difference between product 26-229 and 26-121. Their measurements are pretty much the same except one is slightly longer. The screw positions and the width on the edge are the same. One measurement is not shown is the width of the triangular latch that springs out and locks on to the r ... (cont.)