Viewing all customer Discussions for:

10-324 24" Shower Sweep With Drip Rail

Can I cut the 24 inch drip down to 21 inches to fit my door? Does it impede closing the door if correctly installed? Do you have a vertical drip guard for the hinged side of the shower door. Thanks. Jamie B.

I need to replace a black rubber sweep on a shower door. I do not know the door manufacturer. The sweep is about 3/4 of an inch wide and has a semi round about 1/8 in top. See photos. Where can I get the rubber sweep or do I need to replace the sweep holder also? Thanks! For your assistance. Don ... (cont.)

The photos are showing 2 sections of inner shower door one with seal in place and the other with seal missing from extrusion. The last picture is just of sliver of the piece that fits in door. I purchased a piece 10-319 but it isn't even close to correct piece flap is too small. Hope this helps. Tha ... (cont.)

Hi. Water escapes my shower, and I was told I am missing the door sweep. The ones on your site seem to have the screw holes in different places than mine. This shower door is 27" wide. It seems I would need a 25" or 26" door sweep. There is 21 1/2" between the screw holes. Do you sell anyt ... (cont.)

Here are 3 images and a sketch of the gray vinyl sweep I am trying to replace. Kindly let me know if you might have it. Thanks

Looking for hinged shower door sweep. Measures 1 1/8 wide less than 1/8 thick. Color not important.. Need 24" piece. Appears to be flat without any visable extruded top. Doesn't install in slot. Held in place by 3 pan head screws holding top plate in in a.compression mounting.

I bought part 10-324. What do I install it with? It didn't come with screws or anything.

The photos are my shower room door. It needs the bearing to close the door tightly. The diameter of the hole is about 0.7cm and the total diameter (including outside cover?) is 1.2 cm. Also, I need to attach blockage to the bottom of the door to block water leakage. It was consisted with aluminu ... (cont.)

Hello, I am trying to find this size replacement part for my shower; however, the one I currently have has 3 screws holding in place and it looks as though your product may only have 2 places for screws, is that correct??

I need a tough vinyl or rubber sweep with a t-shape, no more than 1/2 inch wide to slide into the opening in the attached picture. the sweep itself, which seals the area between the bottom of the door and the frame, is about a quarter inch wide

What is the exact width of the 10-324 drip rail?

I ordered the bottom flap drip for the 24" shower pivot door. Which screws do I need to buy and where to put them on the new strip also which way does the new strip go

I need this part and no stores carry it. It's 21 inches long. It's the drip rail for my stand up shower and it's a framed shower.

I've got one of those builder installed framed (chrome) shower doors and am in need of a replacement. I saw the 24 inch which seems like it would work but when I measure my existing door it appears to be 26 inches from edge of door near hinge side to the end of the door just before the magnet. Obv ... (cont.)

I need to find a replacement for my shower door sweep. The tee part is one fourth of an inch. The sweep is three fourths inch wide. I have been unable to locate a replacement for it. Hope you can help.

Does the back of the sweep have an adhesive so it will stick to the shower door as well as the two screws to keep it on? My old one did and that is reason for question.

Door sweep split. 2003 Coastal product. 21" long by 13/16" d by 1/8" top bead .I tried 1 on Amazon but it keeps slipping out.Do you have any thing similar?

Unable to up load pictures from my Computer you will have to go with has been provided. I can only go with a verbal description its 23.5 " long and it attaches to the bottom of a Aluminum framed glass door. The area of attachment on the door the aluminum part is 1.8' in width. The width is 1' wide ... (cont.)

The bottom flap or water stopper needs replacing. Do you sell that part and the screws? Please advise, Tracy

Please review the attached photo. I was wondering if you were able to assist me in finding a part that is similar to what I have? Any help is appreciated.