Viewing all customer Discussions for:

55-195 3' Vinyl Glazing Bead, Bellview

dimensions are approx 7/8" across x1/2"deep marlin seems to no longer do this kind of window. they were triple "pane" with the inner one a special film. they were "special" but not in a good way: construction was crappy, leading to broken seals within a very few years. any clues on compatible glaz ... (cont.)

We recently purchased a house with single-hung, single-pane, Alenco aluminum windows that have no visible number and need to replace the white vinyl glazing beads, weatherstripping on the bottom sash, and some of the channel balances. In order to remove the sash, it appears a part above has to be un ... (cont.)

Hi - I'm looking for plastic glazing bead for some Milgard bronze aluminum windows from the mid-1970s. Overall dimensions are 11/16 w (may have compressed a bit over time) x 3/8 h. The "L" shaped flange is 3/8 (side attached to arc) x 5/16. The arc is 1/2 from point to point (not including the small ... (cont.)

I'm looking for about 12 ft of bead glazing for my windows. One item number from a website says it's Bellview 900-16683 (wht). In my pics it's kinda smashed. Thanks in advance. Jim

I need a few of these. It's like a guide for the screen. Thanks

The snap in shown is 30 years old, and I have lots of windows with snap in cracks. I'd like to order more of this type of snap in to replace several windows. Do you know what part I should order?

This is from a mid 80's aluminum window, dual paned. No markings on the windows to identify manufacturer. It is 5/8" diameter and the straight perpendicular part is 3/8" long. Please help identify as I need to replace it around my windows. Thanks.

This piece is from a kitchen garden window, interior. Molding?

Our windows are 35 years old. The vinyl weatherstripping is cracking and falling apart. I would like to replace them but have been unable to find a replacement. They are bronze color. I ordered from you Bellview Item#55-195 to sample using it as a replacement. In the second picture it is on the left ... (cont.)

Our 1988 aluminum Milgard windows work fine, but the plastic glazing bead is cracking apart. We're looking for replacement parts. Can you tell me what I need to order?

I'm trying to locate these two parts. The one on the left is a screen retainer of sorts - 1.5-inches long & snaps into the exterior side of the sash to support or center the screen. The part on the right is a 1/2-inch wide sash guide that is screwed to the frame and clips over the edge of the sash ... (cont.)

Any idea what part number this could match to?

In my bay window (not openable one/stationary/picture), I notice the exterior rubber seal/glazing bead turned rigid and protruding out needing replacement. Please help me with.. - identifying the right glazing bead. -help me understand what is holding the sash in this window model, if I pull off ... (cont.)

Hi! I'm not able to find these glazing beads for my old aluminum Milgard sliding windows. The size of the panel where the glazing goes is 35.5 x 30 inches. The length of the longer glazing bead is 33.5 inches after being cut diagonally. Please advise. Thank you, Brar

Depth 3/4" ,bead width 5/8" ,bead has groove on left side,bead height 1/2"

Hi there, Looking for this snap-in glazing bead for Milgard windows, aluminium double pane, probably from 86/87. I tried looking through your site but didn't seem to find a match, please help. If there's a replacement, can i swap the bead in place or I have to take down the pane to do it? If ... (cont.)

The window frames are made of white plastic, like PVC even the glazing beads are black. White color would be better I think. Long lip on the glazing beads goes partially in between the frame and the double pane glass (please see the attached picture). Thank you Ned

Hi, I'm trying to replace this black glazing bead. Not sure what the window brand is. Any suggestions? Thanks, - James

I'm looking for a replacement part, though in white.

Looking for Vinyl Snap-in Window glazing with the attached profile and rough dimensions. I have no idea who was the original manufacturer of the windows. I didn't see a match in your stock profiles. Thanks, Jeff