Viewing all customer Discussions for:

81-282 MI Patio Door Roller, 1-1/2" Dia. Concave BB

No marking or numbers

These rollers came off of sliding patio doors in a condo in North Myrtle Beach, doors in which lead to a balcony on a second floor that gets riddled with wind, salt water, sand, moisture, improper care, etc. A few of the other rollers crumbled as we removed them, as did the bottom of the sliding p ... (cont.)

Unfortunately, I do not have all the measurements or pictures that I need hoping you can identify it with the part number. If not, I'm at square one thanks for any help you can give.

Trying to replace 2 single roller patio screen door adjuster assemblies. Both labeled DISCO 1165. You have anything like that? I can't find them anywhere on the internet.

Hello, Please let me know if you have the following rollers or ones that are compatible. MBC 1116 See attached Thank you, (Suggested 81-282) All the measurements are correct. The holes on the top are different but does that matter? See attached. If not, how do I go about placing an order for ... (cont.)

L 2 1/2" H 1 1/4" W 3/4" Wheel 1 1/2"

Hi. I'd like to replace these rollers. The door gets major exposure to the elements, so I'm open to suggestions, as there's a bit of rot where these rollers are found. Thanks, Mark

Marked: Delta 1165. It is about 20 years old. The box frame is 2-5/8" x 1-3/16" x 11/16". The wheel diameter is 1-1/2" and made of metal.

Hi, This is an alluminum door from the 80s. I started taking it apart, but stopped short of removing the actual roller assebly, but you can see it in these photos. Single wheel. The door is 1 inch exactly and the wheel is 1-3/8 -see photo. In the "bottom rail" photo, I've lifted the side to exp ... (cont.)

DISCO 1165 ROLLER 1 1/2 Depth 1 3/16 Width 3/4 Length 2 5/8

Approximately 1.5"x3"x.75" (HxWxD). Wheel is 1.25" diameter. Marking on top says "ASTR BEC OMCO" in a circle

Could not find anything matching in your parts pictures. Do you have anything that could be made to work . There are no names or numbers on the roller assembly or the door. The wheel is 1 1/2" metal. The assembly is 2 1/4" long without the tab, 1 5/8" tall and 5/16" thick

Please help me find replacement parts. Thank you!AJ

3/4" width, 1 1/16" height, 1 1/4" wheel diameter. Wheel is metal

Please see attached. I need two rollers, one for each end of the sliding glass door. Thanks. Marty

I need these roller there for two different doors

Hi I was hoping someone can help me find replacement wheels for attached picture. Top of bracket reads "ASTRCBEC OMCO" Thanks Matt

I'll use the following terminology: vertical frame member, horizontal frame member, 4-sided bracket, 3-sided bracket, roller axle. I'm trying to describe the door in a way that makes my terminology clear. The door has a vertical frame member that runs the height of the door that seals to the glass. ... (cont.)

I am looking for replacement rollers for an Alenco sliding glass door since one roller has completely failed (roller fell off). The door handle assembly is a secondary concern since it still functions and could be replaced later. The broken roller assembly is shown in two of the uploaded pictures. ... (cont.)

I looking for replacement rollers and possibly the housing as well for the attached images. The house was built in the 57 and I think the sliding glass door / sunroom was added early to mid 60's. The frame is entirely aluminum . There are 2 rollers on each door panel . Each door is 48" x 81" approx. ... (cont.)