Viewing all customer Discussions for:

32-061 21-5/8" Self-Closing Drawer Slide Pair

Hi there,From other posts, I'm thinking these plastic clips with pegs are nearly impossible to find. The pegs broke for one drawer, so now the rail won't attach to the back of the cabinet. I'm guessing I'll need to reinforce the back with wood and find a new rail system with screw-in back mounts. An ... (cont.)

Hi,I have a cabinet drawer rail from 1985. There are not markings listed. The rail it sits on is 22.5 inches from the very back to the very front. The top part that rolls across it is 21 inches. It sits very flat to the cabinet around it (not much spare room is needed around the drawer for it to sli ... (cont.)

Good afternoon, We are looking for replacement drawer slides for the attached pictures. The one glide shows #PMI-CM565L. Are you able to quote?

I need to replace the actual drawer but the drawer slide and bracket need replacing as well. Can you help find the parts or suggest something similar/better? The bracket is cream/off-white and holds the drawer slide at a 90 degree angle. The bracket has plastic tabs on the back that holds onto the ... (cont.)

I am looking for drawer slides measuring 19-5/8 long stamped with unigrass 6600. The roller is 3/4 inch Thanks, Tom

I need a replacement slider for a Merillat cabinet drawer as shown in pics. The slider wheel is worn out. Thanks

I am trying to find where I can purchase replacement drawer slides that match this size profile but are longer. The only identifying marking is "UNIGRASS 6600". What I have installed now is 50cm long which leaves about a quarter of my drawer under the cabinet and not conveniently usable. The piece a ... (cont.)

The cabinets were installed in 1992 by the previous owner so I do not know the manufacture. The inside dimensions of the socket are 3/8 by 15/16 and 1 1/4 deep. The exact replacement would of course be best, but if there is one that requires screw mounting with everything else correct then that wo ... (cont.)

need 3 sets. Side mount. The outside metal circular tabs fit into metal frames installed inside the cabinet. Cainets installed 25-30 years ago.

track back plate has broken so there is no suport for the side rail. I think maybe I need 32-089? My side rail is 1" wide. The back plate is broken in a couple of drawers--1 is a kitchen utensil drawer that is about 22" deep and other is a desk drawer that is about 16" deep but except for the len ... (cont.)

Looking for p/n for a rear press-in drawer slide mount (plastic piece) as seen above in the picture.

I want the rail that your part #32 040 goes in

Hi, I'm trying to fix cabinet from 90s. I can only the brand Unigrass. The rail attached at the bottom of the shelf is 21 5/8; the rail attached to the cabinet is 23 1/4. Would 32-061 work to replace the old one? What bracket should I use? Thank you.

I need the left drawer guide for a 22 inch drawer

Hello, I have a drawed that is need of repair. I need to replace the left & Right side rails that mount to the bottom of the drawer and I need to replace the left & right side rail that mounts inside the cabinet. I have a unigrass 6600 bottom mount drawer slide that is 21-5/8". The track that th ... (cont.)

Hello I am looking for the above brackets used in the kitchen cabinet drawer slide support. Attached are front and back faces of the bracket. Would appreciate if you could assist in finding the same.

Hello: One of our kitchen cabinet pantry's drawers fell and saw that its rear bracket for the drawer slide was broken. Was looking to see if you have this bracket. The attached 2 pictures show the broken one & a working one. Looking forward to hearing from you. Thanks

Part is broken (both sides) Mounts to back of cabinet.

I am looking for a drawer socket for a Scheirich PPW098 88. This socket slides on a metal anchor strip that is screwed into the back of the cabinet.

That plastic/nylon piece attached at the rear of the cabinet that the rail attaches to.