Viewing all customer Discussions for:

90-183 Sash Lock Keeper, 2-1/4"

Lock for window sash

These are Deco parts - found the part numbers online by measuring - but can't find parts.

Screws are 2 1/4" apart Catch is 2 3/4" long x 1/4" wide Sits on top window The other piece is 2 3/4" long x 1" wide.

Hello, Please, kindly help identify the appropriate replacement for the Latch in the picture. There are no labels or markings on the window to indicate the manufacturer. Latch measures 2 1/2 x 9/16 without the tip 2 9/16 X 9/16 with tip Thanks a lot

these seem to a #6 thread with a #4 head. where I can buy them?

Missing the catch. Would like a new set please. The swivel lock is 2 3/4 wide x 1" deep Me a The catch is 2 7/8 wide x 1/4".

The latches shown in these two pictures do not catch. Maybe the windows have warped enough that the sweep is not long enough to catch. Do you have any ideas? The sliders are double sliders. I ordered the 90-180 and the 90-183 keeper, but they are exactly what I already have that doesn't work. You ... (cont.)

Screw holes on locks and keepers are each 2 1/4" center-center. Underside of lock body has raised "1527". Top of lock body has raised "LOCK". Underside of lock cam has raised "1490". Underside of keeper has raised "1513". Lock body and keeper are each 2 7/8" long. Thanks, David N. Mann, PS My ... (cont.)

Can you please tell me the replacement sash locks and associated hardware (screws) to replace these dual locks for a full sized window (30" x 53 1/2") that is inside of a shower. The dual sash locks and hardware have to be able to withstand water. The pictures are attached w/ a ruler for scale - the ... (cont.)

Could you please help me identify the correct size latch keeper to replace my existing keepers on Jeld Wen windows. Photos attached. The original keepers are nylon material. I purchased keepers from swisco but had to return them because the keepers were to tall and the latch wouldn't catch.Thanks,An ... (cont.)

Hello-I've been trying to locate the "receiving" part of my window latch, as shown in the pictures. The part is a 1/4" thick. The part I photoed is broken. I need 2 of these if you have or can locate them. Let me know if you have any questions. Thanks Chris

Attached is an image of a window with the bar and latch in place, and an image of them missing. I need this bar and replacement latch. the bar is 20 5/8" long. I appreciate your help with these parts. Thanks, Dan

I need the window lock replacement for a lost one.

Do you have replacements for the attached photos? I tried looking though the website, but did not see an exact match. If these are unavailable or discontinued, do you have an alternate type that would work? I need 10 sets.

I can't seem to find which window lock model these are. I can't find a serial number on the lock or window. Have tried a few replacments off amazon but nothing has fit. I'd rather replace the locks then get whole new windows. I would need about 20 of these locks

Original Window Vertical Sliding Window Window Latch. Holes are 2 1/8 apart and 3/8 from the edge. I can provide more exact measurements if needed. Die cats material.

Hello, I'm searching for a window sash lock and keeper. The lock installed is Alcan with screw holes 2 1/4 inches apart (photo atch). The tongue extends from the lock body 5/16". The lock ledge is 13/16" wide. The keeper ledge is 3/8" ( photo atch).I believe the keeper would look like Truth Wind ... (cont.)

I have 7 windows that I would like to replace the balancers and locks please How do I go about picking out the right parts please I have in two windows with 3/8 balances with 27" length Could really use some help please

I gave you a picture of the sticker from the window. I need 4 sets in white.THank you .Donna

Trying to identify proper sash lock replacements. Screws are approximately 2 1/4 inches apart