Viewing all customer Discussions for:

Door & Window

Details in 3rd picture

I need 4 channel balancers 33 2, but I cannot find them when I search for them. It is a plain channel balancer for a tilt window. Please tell me what is comparable to this channel balancer.

This is my mother In-laws door. Unfortunately she does not know the brand of door and I see no markings on the door or lock. The outside handle had the lock on top. Inside it is a 2 piece set up with the lock up top and the handle on the bottom. Is this anything you selll? The handle and lock no lo ... (cont.)

These are mid 90's builder's grade windows, no brand label. They are beige but I can paint if only another color is available.

I need to replace the crank part and the arms of this mechanism. It is a small casement window in the bathroom, approx. 14 inches in width and about 24 inches in height.Thank you,"Vince

Wheel diameter: 1.25 inch Assembly dimensions: 5/8 x 1x 2 1/8 no names or numbers

I would like to order a new sliding door handle

2365 HT 24in length

Hi there, need to replace the casement operator I think. Won't open/close the window or will open it but not close. The cover says Crestline so I'm assuming that's what the windows are. The parts say Entry Gard Truth. I think I found the part on your site but just want to make sure I'm correct. ... (cont.)

Channel Balance is 15" long and 1/2" wide Stamped with 14-2 Window weighs 11.5 pounds and hoping to go up to 14-3 because windows are sagging with the 14-2. Looks like 15" Series 380 Channel Balances and just wanted to double check with the pros before ordering 4 of them to replace balances for 2 id ... (cont.)

Thanks for helping me with my spiral balance replacements in the past. Your videos are very helpful. For this new type of window, I need to identify the right coil part number. I'll send you a better picture, but I want your advice about where to make the cutout to remove the broken spring. Is t ... (cont.)

Good day/night, Hello everybody, I'm trying to find the latch or handle assembly to replace the broken one I have please. Thank you kindly

I want to replace a number of crank handles like the one shown with a lower profile handle (a T handle?) that will not interfere as much with shades and will protrude less into hallways. The installed handles are stamped "TRUST" with number 45240 8. Color looks to be black, but could be a dark bronz ... (cont.)

We are having issues with the springs constantly jumping past the window and losing the connection. So the windows don't open. We have reset them several times. Thinking a replacement may be needed but can't figure out the exact part to order.

Your balance springs are the closest thing I have seen on the web to the broken ones I need to repair.

I purchased a S770-34, and it is the proper channel balance, however the clip is not correct, as shown in the image. I don't have a spring hook otherwise I would disconnect the spring from the retaining pin, releasing tension and tie on the new hook at the end. What are my options at this point? ... (cont.)

I have a cracked slider door handle marked SGDH-3-A-1. I will send pictures. Can I order this part please?

My tubes are inside a plastic case, and flexible vs rigid. The "spring" case is 28" long, and the tips appear yellow. My lower sash tilts, tops are stationary, and sashes weigh between 19-24 lbs. These all failed when the top eyelet broke where the screw held them to the channel. I don't see any ... (cont.)

Old window!!! Top 2 screw holes 1/2 inch apart Bottom 2 screw holes 3/4 inch apart Top screw to bottom screw 5 1/4 inch apart Left handed

My door handle is broken and I bandaided it for a while but now the locking mechanism is broken and it won't latch . What do I need to order to replace the inner, outer handles, and locking mechanism that has the hook that latches the latch. It is keyed . I'm looking for the whole replacement . 82-0 ... (cont.)