Viewing all customer Discussions for:

Door & Window

need replacement recommendation for balancer spec per photos and subject info

(1) 23-273 : 95" Bottom Concave Roller Track You don't carry this anymore? what can I substitute for this if that is so?

Hello, I was so excited to find your website with so many useful information and parts for windows. Several of my windows' coil balances are broken. The attached photos are from the same window. My questions are: 1. What are parts # for coil and pivot bar that might fit this window? 2. Since thi ... (cont.)

I had the channel balance break in two different window with the same size. I don't know the sash weight. The balance is 25" long and the plastic connectors look to be a fairly standard winged connector.

27" long (metal); 1/2" wide; 5/8" deep; nylon end near pulley has wings; other end does not have wings.

Appreciate all your help. Sorry my drawing is so bad. Hopefully you can read inches " or mm measurements I put down. The example is a right side latch but need right left pairs.Initially I need 8 right/left pairs (16 total latches and have 4 more dwellings to do.Thanks again.Jay

7ch on coil spring and 7L and 7R on the white housing. The springs are broken.

older Anderson windows. i think they are 200 series. Andersen Sash Balance. do you have a replacement? i will need two.on the other side of the unit are the following numbers11600-171227 2-88

Need balancer parts and button for top to tilt out.Just want to know if there is a catalog or picture of parts to be sure to order correctly. In need of balancer parts and button for top to be able to tilt out.

The channel balances just have 28D stamped on them. I've included a picture of the existing channel balance. Just want to confirm that this is the 29" Series 390 Channel Balance 2840. Thank you!Also, window sash weighs 23 pounds. The metal portion of the channel balance is 29" in length and the s ... (cont.)

Hello. I need two 13" channel balances Displayed imprints 13 2 BSI PE. I will also need instructions for installation. Thanks, Dorene

Hello, We are in the process of remodeling a house that was built in 1971. We are not replacing the windows as they are in decent shape. We would, however, like to replace the hardware to something more modern in black color. Do you have anything that is compatible?

Metal channel length is 25 & 5/8 " Stamp is 25 4 B.S.l PC House was built 2004 Need 2 balancers

Hi. I have Jeld Wen wooden guillotine windows. I am looking to buy a dozen of these metal pins that enable the windows to open and stay open. They also act as pivots for top open pivot cleaning.

Hello, Need part numbers for 5/8" Spiral Balances 30" long And pivit show as shown in the picture

Hi, I'm trying to find a replacement for this internal latch tilt for my window. It's about 3 1/8 length, 3/4 wide, and 1/2 height. I came across this one on your website and it looks close but I'm not sure if it will work. The hole you see in the pictures is for a screw after I slid in the inter ... (cont.)

I have numbers on the balance that read: E7 927 1084 AND ALSO 11600-17 WHAT BALANCE DO I NEED TO ORDER?

I need to confirm the part. Seems the right and left side are different. One side is 3140 and other is 3140x. Both are 32 inches.

Hello, the enclosed photo of my coil balance spring has #6.5 35. Do I assume the number 35 has nothing to do with the weight? Also I seen on your site one similar to mine but it's made out of titanium. I doubt if mine is titanium but I just want to make sure. Thank you, Dan

The channel length is 26.75". It is stamped with "26 4". These are Jeld Wen windows manufactured approximately 2006. We need to purchase 2 of these balances. Thank you