Viewing all customer Discussions for:

Door & Window

There are no markings I can find. The frame is metal and appears to be 30 years old.

I have a 35 lb window double hung tilt sash window that will not stay open. Each side of the window uses three series 180 coils, one 15-087 and two 15-086 tandem housings (coils appear to be marked 6 lb / 6 lb / 7 lb - so it should provide a total balance weight for ~ 38 lbs). The lower sash r ... (cont.)

I have a 1/2 inch extruded aluminum patio sliding screen door that has the Swisco lock #84-227 on it. I don't like the grip of the lock. Is there another lock that I can use as a replacement. The screws are 3" apart and the door is 1/2" thick. Thanks in advance for your help.

This is a broken part of a corner key for my screen frames I will need 16 of these and some new knife latches. These screens are about 20 years old and most of the keys have broken in half. The one in the picture is the best specimen I could get. I hope this helps. It is 3/8". Thank you, To ... (cont.)

I own a Pella Storm Door, Model # PSD4001. The door sweep at the bottom is bad and I need a new one. It looks like a y shape that fits into the door? Can you please tell me which door sweep I would need for this Pella door?

I have an Anderson crank arm that needs replacing. The Anderson part # is 1361308. Is the replacement part the 39-095 or the 39-151?

I have a Pella sliding glass door that is missing the strike plate. Here are two pictures - the lock recessed in the door and the holes in the door frame for the strike plate. can you tell which strike plate I need from these photos? eric sacknoff

I am trying to locate this top sash guide for some quick window repair before closing on our home.

I am looking for a replacement locking mechanism for an awning window. The only marking I can find are on the metal part which has Patent No 2997754. Do you have this item available? Thanks.

How do you take the screen door apart to expose the roller assembly?

I'm looking for the corner repair hardware for my Traco window screens. The windows were installed in 2004. I believe that Traco is now a different company because it has since been taken over by another company and the brand is now sold from retail home supply stores.

I have a spiral balance that is 28" in length by 3/8" in diameter. It has a red tip and the spring end has two 1/8 diameter roll pins that are separated by a measurement of 1/2" center to center. Each roll pin is 1/4" in length and is attached through the end of the spiral balance. I need th ... (cont.)

hello I'm looking for the sure lock -lock mech that goes with the 39-404 handle , a left hand ,,,do you carry such a beast? thanks for you time....if so I'll get the DLO AND PICS

Do you have a balance with a part# 2230 stamped on it? Also the attached lock assembly? Thanks

This is an image of the part I need. It measures 1 1/4 wide and 1 7/8 tall. It has 3 springs for lifting. The springs appear to be fine. I need the lock shoe.

Hello, I was looking at your 1/2" Wide Channel Balances cl/1_2-inch-Wide-Channel-Balances to replace a broken one in my son's room. The length of the original is 26.5" (please see photo 3 for stamp) I see that you don't offer half sizes? So I was wondering if I could just get away with a 26". I ... (cont.)

Vetter Windows is out of business. I have been unsuccessful to this point at finding this replacement part.

I need to replace this broken window lock. Please help me find the correct part. The screw holes are 2.25 apart on center and the overall length of the part is 2 & 7/8. The width is 3/4 and the part has alenco imprinted on it.

In need of a replacement for this RH window latch. The only marking I can find is the 627 on the back.

Looking for these two drawer guides that go on either side of my drawers.