Viewing all customer Discussions for:

Closet

Hi, please take a look at the attached. I have these rollers on two different sets of sliding closet doors in my home. On Saturday, the plastic part on one door cracked. I went to Lowes and Home Depot to find replacements, but they had nothing similar. So I called Paragon Schmid, which is the co ... (cont.)

Your 23-041 appears to be essentially the same as the ACME 4011 that I need to replace. Will it work as a replacement? If so, I assume that I should order 2 and replace both bottom roller assemblies, even though only one is broken.

Door came off top track - we removed door. Have screw from top track but no cap for the pin, if there ever was one. We cannot find replacement on your site o hope you can recommend what we need. This door has matching bifold doors (two) in the same hallway so if we can avoid replacing all the ... (cont.)

We have three mirror closet doors 8 feet high. The track is 10 feet long and has a convex track that takes Cox 21-717, 21-767 concave rollers (6 of them). The present track is badly bowed and rollers have chunks missing on them. We are having difficulty finding anyone to help us. Can you please advi ... (cont.)

WOuld you be able to supply parts for these doors.

Do you have any closet door rollers with a half inch or 5/8" wheel? It is just a wood sliding door. The rollers are missing from one side and I haven't pulled it off the track to take out the other side (am trying to avoid that if possible). The rollers are convex. I could get by with a setup wit ... (cont.)

this number is stamped on our door. what parts would make this work?currently it off the track 50309941 246505

The following pics I need the white part that fit this railing. Please let me know if you can help This is the part that slides the bifold door in the track .

I need to replace roller on a mirrors sliding door. Your 23-225 is close but my top hole measurements is 2 7/8.

Door has part #6956 on sticker. 1/4 inch hole. Apx 5/8 inch lip. Apx 1/2 inch high. Have tried the Swisscom part # 21-109 fits the pin but the lip is only 1/2 inch do you have any that have a bit larger lip? I work at a nursing home and need quite a few. Nathan J

Manufacturer (hdi) numbers stamped are 4021j and 4050j

Attached are pictures of my 72

I need 2 Bottom Rollers, 1 Bottom Pivot, and 1 Top Roller. I can't find any markings on either the parts or the door. Each is about 4 inches long. Any help you could provide would be greatly appreciated! -Don M

I have 1970 era sliding mirrored closet doors. The rollers hang from the top of the door. The rollers spit out the bearings and I can't find replacement parts. An aluminum rectangle piece about 2.5 inchesX 3/4 " wide slips in a channel vertically. It has the wheel on top at a right angle to the al ... (cont.)

I have SEA Inc. mirror closet doors. The plastic rollers are worn out. These are bottom installed parts. SEA no longer makes them? The part is 1/2

I need a replacement roller for Stanley 17- 4116. I have read the previous post that states the replacement rollers are 23-222B. The pictures on the website looks different from my rollers but the item in the video appears similar. Can you confirm which photo is accurate representation of what t ... (cont.)

Need this part. Do you happen to have it?

The photograph shows one of two top rail guides for a sliding glass closet door. The rectangular plastic guide on top of the other guide has broken off and I need a replacement guide. The only markings on the guide are "Acme U.S. Pat. 3750337". Can you help me find a replacement door guide? Than ... (cont.)

Hello, I need some help identifying replacement parts. I recently purchased the following hardware on order #1009999 thinking it was what i needed but it ended only 1 item was a exact match and the following is a description of the parts i bought and why they wouldn

Can steel bifold closet doors be trimmed if it's too long? Is it possible?