Viewing all customer Discussions for:

Closet

I need replacement rollers on my sliding closet doors. Can't find anything that fits. These are from '95' Wardrobe and Bath Specialties in Modesto, Ca. The new replacement they sent will not fit. (See pic). The top 'wing' measures 4" which has one screw in the wood frame and the bottom has one ... (cont.)

missing the bottom end glide the photo is from another door that is in condo. Thanks Eric

My daughter's closet has three large mirror doors that operate on a two door track. The doors constantly bang into one another. Do you have a 3 track bottom track that you sell that would allow all three doors to slide independently?

Can you tell me the part number for this? I also want to know if I can just ordered the beige part because I don't know how to get the metal part off of the mirrored door. Thanks Nicole

Looking for a replacement for my mirror door wheel. It is a 1 and 1/2 inch plastic diameter wheel that is in a metal housing 2 and 1/2 inches long and 9/16 inches thick. The wheel has the number 608Z, and the metal is stamped DNW. It is secured with one screw.

Please see pictures. 3/4" chamfered nylon roller, 3/16" offset, mounting holes are 1 and 5/8" apart. This is for the "front" door.

Good day gentlemen, I bought a closet on sale, and it was without the top guide. There are a number of the top roller DSH - 20121, looks like you have the directory. Tell me the internal dimensions of the guide or prompt where in Moscow it is possible to buy accessories. Translation via Google trans ... (cont.)

HI, I AM LOOKING AT YOUR ITEM #23-047 DOOR HANGER, 1/2" OFFSET. I SEE THE NYLON ROLLER HAS STRAIGHT EDGE. ****** I NEED THE ROLLER TO HAVE A CONVEX EDGE******* DO YOU HAVE A DOOR HANGER WITH THE SAME DIMENSIONS AS YOUR ITEM # 23-047 WITH A CONVEX NYLON ROLLER, NOT THE STRAIGHT EDGE? PLEASE ADVISE. L ... (cont.)

I need a plastic 'pivot rod CAP?? it is 1/4" diameter on the inside where the metal spring loaded rod fits, this cap part is abt 1/8" deep, and has a 3/4" diameter base -about the size of a nickel, that actually slides back and forth in the track. the only marking I can find on the bi-fold doors is ... (cont.)

I purchased some closet door guides 23-207 and installed a couple on the bottom of my closet door but the problem is the new guides are shorter than the original ones and don

Picture of my Sliding Closet Door wheel assembly. Looks close to your part # 23-064 however, the vertical hole-to-hole height is 2 1/2". Your part looks a bit taller... No markings on the door or wheel. Any advise or guidance? Thanks...

My bottom Track looks totally different than any I see on the website. Can you tell me the part #'s for top & Bottom? My bottom track has a center that you have to nail on top of a narrow strip of MDF or wood, in order to install it.

Do you sell this type of roller for a sliding mirror door?

What is the roller made out of? Is it hard plastic? Soft rubber?

Can I get this part or a replacement part

I am looking to replace the two tracks for a couple of bi-fold closet doors. I was curious if that was something you had and what it might cost.

Looking to find a replacement track and wheel. We need it in gold trim. Please let me know if you have anything. Thank you

Just purchased 2 metal bifold doors that does not have a track . they are 36 x 80 which track would be the one I should get

I have a Home Decor Innovations model 425 sliding bypass door. It has a top and bottom door track with the weight of the door supported by the bottom door track. I am looking for hardware to build a sliding bypass knee wall door with a rough opening of approximately 132 inches using the same hardwar ... (cont.)

I manage an apartment community and 50 units have Leigh Full Vu closet doors model 8433. We are looking for top left pivot holder, similar to the pin pivot bracket of 21-205 but there is a portion that folds and when the screw is secure it locks it to the track. We recently ordered the Bifold Do ... (cont.)