Viewing all customer Discussions for:

Closet

3 5/8 * 72 length and width of track. gap between two tracks is 1 5/8 the glass is made by stanley i need to know if the 23-242 is the correct track attached are images of bottom track, lower and upper wheels.

I have rear closet door roller and the size length is 1-3/8" and the rollers size is 3/4 ".I want know can I go with a different size rear closet door roller like the one u have shown #23-010, Andrew C.

Hi, How do I adjust the dial so that my closet door will sit straight against the door jam? Thank you.

I have a closet mirror door using CW part #RM-G1005. I am wondering they have a part # for right corner and left corner of closet mirror guide or they are the same. I need whole set of this closet door guide. Can you let me know what part # I should order? And how to install this closet door guide i ... (cont.)

Looking for 6 foot replacement track for mirror closet doors

one of the wheels stopped rolling and I need to replace it. I prefer to replace both of them. There is a sticker on the door from Charmac, Inc as the manufacturer of the sliding wardrobe mirror door

Hi - I am looking for a roller assembly like your 23-064, but I need to know if the concave wheel is 5/16" wide. The only number I found is on the actual wheel - it says Toronto Canada 9360. Thank you for your assistance. Margaret Estenes

I am sending photos of my Cox roller 21-767. Do you have these parts? Can you ship four of these rollers to Buenos Aires?

recently purchased your bifold door pin cap item 21-100, but discovered that although the outside dimensions of the cap lined up perfectly with the caps that needed to replaced, the original rods are larger - they are 5/16". Do you have another product that would be usable.

Please help. We have 2 mirror sliding g doors. Total width together is 60inches. We only have one wheel and no track. Can you help?

Seem I have an odd sized door. House was built in 1959 The rolls appear to have a 3/4' offset and flat wheels. House was built in 1959. Thanks again

I have a set of sliding doors in a bedroom closet. The rear door of the set has good roller hardware. The front door of the set has no hardware, as it has broken throughout the years. The rear door hardware measures as the following hardware, found on your site. 23-186 Rear Closet Door Hanger, 1 ... (cont.)

Can I order 8 of these, and how much would that cost?

This track has rusted out. It is 60" as there are two bifolds.

Please take a look at the enclosed photos of the subject wheelset. The wheelset is original to the house, circa 1962. It is aluminum with the markings "To Lower Door" around the adjusting screw and and the words "Pat. Pend." above an "LB" insignia. The "LB" insignia is inside a square box and loc ... (cont.)

This assembly looks similar to your part # 23-028 (concave wheel). Width dimension of my part is 2 1/2" versus 2 1/4" with the 23-028. What replacement part will work best?

Attached are the pictures of the closet door guide. Let me know if you do carry this.

I am wanting to mount a framed mirror that was once mounted to a dresser to a tiled wall for a vanity. What kind of fastener would you recommend? I would prefer not to drill through the front of the frame. Rather, I would like a hidden method. The mirror weighs 22 lbs. Thanks

I have a damaged lower track of a Monarch mirror sliding doors. I want to replace it. The dimensions are 3 inches width, 1/7/8 between guides and 48 inches long. I would like to know the availability and cost. The 23-270 dimension between guides is 1/21/32" and mine is 2". And finally the height of ... (cont.)

My name is Paul and I am doing some work in this condo and the lady wanted the door fixed. This is the bottom guide for a mirror bifold door. Owner says she bought the door at Lowes but have been unable to find the door or this part she does not know manufacturer. This guide runs in a track attached ... (cont.)