Viewing all customer Discussions for:

Closet

1) For 23-242 72" bottom track and 23-246 72" top track, can these be trimmed onsite? How do you recommend trimming? My opening is 69 3/4". Of course it couldn't be a standard size! 2) is the brushed Ni finish nice or just raw metal?

I have a set of closet bypass doors that have swollen slightly at the bottom due to some water exposure from a leak. One door no longer slides though a 1 3/8 inch wide slide. Can I buy an adjustable slider to accommodate a slightly thicker door?

The plastic wheels are breaking off of our old mirrored closet doors so they will no longer roll. Can't find anything even similar at the hardware stores. Do you have anything that would work? IHC miami u.s.a.

I have afour panel bifold door with a bad upper pivot(the one with the nylon wheel). The pivots are spring loaded. I cannot find the same hardware. your 23-506 hardware kit appears to be a possible replacement. I need to know the following information in order to evaluate it. 1. the length of the ... (cont.)

hello, I just bought a house with mirrored closet doors that have the track and rollers at the bottom. we put in new hardwood floors and don't want to put the bottom track on the wood. I was wondering if I can convert the door hardware and track system to top mounted? if so, please let me know wh ... (cont.)

I think I found the right part but would appreciate confirmation. See photos attached as PDF. Should I replace the entire Door Pivot Pin (Product Code # 21-002) or just the Pin Cap (Product Code # 21-100) ... or am I completely wrong, in which case, would you please direct me to the right product ... (cont.)

I need a 60" bottom track for a sliding mirror door. The shortest one I see in your advertisement is 72". Do you have 60" tracks available?

I need to replace 4 broken mirrored door bottom rollers type product code 23-199. How do you remove the broken bottom frames from the door ? How does the replacement 23-199 insert into the door bottom?

Please help me find a replacement part for my peachtree bifold door bottom pivot bracket. It's nylon with a steel bolt and steel clamp that the bolt threads into. It measures 1.5" long by 0.75" wide. The pivot is 7/8" long and has an I.D. of 1/4".

I was curious if you carry paniflex complete door track system with all the hardware for 4 door bifold

How much clearanace will be left after doors are installed so they are able to slide properly?my main concer is being able to see a fairly big gap between doors when in the closed position..thank you

by any chance does this come in silver color in 48" ?

hi, i'm looking for these parts, wondering if you have them

Dear Sir, I have a bi fold metal doors for my closet, I am missing the pins and accessories , please see the pictures attached , I need 12 pins, Nylinder, E-ring or push nut

Hi, I need to replace the bottom track on my sliding glass mirror closet doors. The name on the back of the doors is Falconer Glass Industries. I'm guess they are about 20 years old. They were installed about then in a condo complex. I can't find anything online. I see that you make part ... (cont.)

Our doors are about 30 years old and are grinding metal on metal because of wornout parts. Please advise on all parts that should be replaced. Please contact me, I am sending photo's and would like to replace all parts that will make the doors run smoothly again

I have a 50's ranch house with wood sliding doors on the closets. Each closet has 3 doors so the middle door is passed on each side. They have a wood floor track and the doors have a plastic guide screwed to the end of each door with a small tang that extends into the wood floor track. This small ... (cont.)

I think I have found some of my parts but would like help putting part numbers to the three items needed to repair my doors. I have attached 3 photos of the three items. please give me a call or email, would like to get started on the doors. Best Regards, Mike

The unit was built in the 1979. We recently bought it. There are five doors like this in the unit. One of the doors is missing the track for the floor and the bottom hardware for the door- making the door nonfunctional. A label on the door says "Benchmark"

I have installed many bi folds but your slide guide is a mystery. Your diagram does not adequately show where these pieces go in the track. The springs are contained IN THE PLASTIC casing so do not cushion the door. Where and how are the slide guides supposed to be installed? I need some help. Pleas ... (cont.)