Viewing all customer Discussions for:

Closet

Hi! This baby is an ACME 4050 bottom slide for a closet door. Do you good folks this or a good substitute, maybe? Notice that it fits into that little slot in the frame there. Thanks SO MUCH for your help! Paul

Hello, I am looking for replacement parts for closet doors which I had to remove for a construction project. I would prefer if there is an easier pin to use than the ones I have in the pictures. Also there is a stopping block in the bottom rail that is missing and I would like to replace it and th ... (cont.)

Hello Do you have replacement hardware for this bifold door? It's super old, date on back says 1971. Neither door set had a complete set of hardware on it. They're in an old mobile home. Hoping you could help with the upper and lower pin replacements. Also not sure the tracks have the pieces they'r ... (cont.)

Hello, I purchased Paniflex bifold door hardware from you for some existing closets, but I have since widened the closet openings and need to cut new doors to fit. I now have 42" and 31" closet openings, the former with four panels and the latter with two. These are the widths at the narrowest poi ... (cont.)

Dear Expert,I need a replacement of the mentioned bottom track/rail. It is made of steel, painted white. The name Stanley is seen on the mirror doors of the closet. The name Pronto Uomo is seen on a label at the bottom of the track. I will need a length of 91.25 inches or 2320 mm.I have included 4 p ... (cont.)

Hello there! I currently have an older 3-door, 3-track sliding-door closet. Unfortunately, one of the top brackets is broken, and a bottom wheel bracket, as shown in the attached image. Do you have any replacement parts available for this particular door? Thank you for your assistance. ... (cont.)

I am trying to replace the broken pieces for a 90 inch metal bifolding door. Can you give me some advice as to what replacement parts I need to purchase?

Hi, we purchased a 1967 mid-century home 10 years ago. In several of the rooms, the door systems need hardware and tracking system replacement. I've taken photos of one bedroom/office that is in the worst shape. Looking forward to receiving advice and guidance. Thank you, Patt

I need to replace two wheel mechanisms on my mirrored sliding doors. The picture I submitted is the one off my door on the left and your mechanism is the one on the right please help me locate and purchase the right units.

Hi. I need to replace three of these upper door guides as the plastic has broken and the doors don't fit/slide.

I need this part for my bedroom closet

Please help me identify the attached bottom pivot. 3/8 pin cap,1/4 possibly 5/16 hard to tell threaded shaft, 5 5/8 long. I would also like the part numbers for the speed nut and clip and the screw lock in the pic. The original pin cap had a wider base to sit on that obviously is worn and missing in ... (cont.)

Has Stanley 1 number stamped on it. Would love to have a replacement part that would work

I ordered (4) of both 1-1/2" and 2"Snuggers for our Bi-fold wood closet doors. Both were not wide enough to stay attached up inside the track. (See attached order sheet and photo.I also attached a photo measuring the overall width of the track. As it shows is it is 1". Then another photo of the w ... (cont.)

Can you help me find these parts?

Hello, I need to replace the track forum bifold closet doors. I have attached pictures. Could you please help me to identify the replacement part(s) I need to order? Thank you.

I need replacement floor tracks for my 1969 fold away bifold metal closet doors - still available? Do you sell a kit to refurbish the door and all the hardware?

Mirrored closet door roller no longer runs smoothly. The metal frame of the roller housing is scraping against the track. Even though the roller unit is securely fastened to the door frame, the roller unit wobbles and sits at a slight angle (no longer aligned vertically with the door). The top part ... (cont.)

Hello, I have the panel closets that use part 23-017. One of my door profiles got bent and I haven't been able to get it straightened out well enough to securely hold the panel and haven't been able to find replacements. Would it be at all possible to point me in the right direction to find the do ... (cont.)

Hi there, the top pin of my metal bifold door how come out and I need a replacement. Can you assist?