Viewing all customer Discussions for:

Drawer & Cabinet

Our Merillat cabinet sliding drawer spacers are all cracking and falling apart - we need to replace the plastic spacer. The old ones measure closer to 15/16" than 1". Would part#32-339 work as a replacement?

I'm in need of a Quality Cabinets kitchen drawer under mount left side plastic locking mechanism. These cabinets were installed in July/August 2007

I either need two left and right replacements for sides of drawers or 12 replacements for the whole bedroom set. This hardware is for bedroom dressers from crate and barrel. The current slides have a spring mechanism which makes the drawer slam at the last part of being closed. If you can recommen ... (cont.)

The only identifying things are the #3613151 and two L's facing each other above the #. I'm redoing my cabinets and need soft nickle hinges but am unable to find them at Lowes or Home Depot. I'm going to need 40 and have bought a couple and had to return them because they bowed out to wide and w ... (cont.)

I am looking for a hanging drawer slides, similar to the ones for keyboard drawers, but I need a full extension, 21 inches. I am hanging drawers that are very close together. 1/2 inch, figured I could off set the sliders so both could fit in the 1/2 inch area between the drawers. I found your part ... (cont.)

Need 2 pair.

Is there an easier method other than brute force to remove the socket piece from a new 32-012 assembly and install it in the serviceable mount piece? Thank you.

Hi,I have a hanging slider socket from a kitchen drawer that has broken. Can you please advise if you have anything that can be used a replacement for the broken socket?Thanks so much. Here's the dimensions of the one that's broken compared to the 32-116: Broken SocketHeight: 4 11/16 Depth of openin ... (cont.)

It is very similar to Rear-Drawer-Socket-Pair/pd/Replacement-Drawer-Sockets/32-012 The part that goes into the wall is the same dimensions. It is missing the oval hole on the top, and has two pegs sticking out the back. The piece that holds the drawer rail is 3" as opposed to 2.5". ... (cont.)

Looking for drawer stoppers for a Bassett Furniture dresser that is over 10 years old. They have not used this type of stop in about 10 years.

Need to replace drawer slides on haas cabinets ,kitchen the plastic back mounts if possible,thank you

This piece is held in by 2 screws.

Hello. I am trying to find a replacement part for a plastic drawer slide in my PA House Armoir. I know we have replaced several i the past, but need another one at this time. Is this something you carry? Thank you for your time. Anne

We are looking for side mount drawer slide socket

it is a 3/8 inset self closing hinge, we need 50 pairs of them. I have ordered several different brands and none fit - the spring area is more narrow than the new replacement hinges, so it will install in original holes but door will sit too far over so it wont shut properly.they are most likely 30 ... (cont.)

Opening 2and 1/8" top opening 1and 5/8"

I am in need of 2 of these. Only markings are left and right. They are 4 3/4 long and 1 1/2 wide at the top and 3/4 wide at the top. I need the left and the right. Thanks

Trying to replace my cabinet door hinges satin nickel or stainless steel. But not finding the same size hinges to fit.The cabinets are pretty old.My hinge reads: US PALMO, 33921420, JAPANI've been to many stores looking for these hinges but not been successful. The hinges that I've found not the s ... (cont.)

I need a dresser rear drawer glide with a half-inch opening for a three quarter inch rail. My old part has no markings. what part number should I use for ordering? Thanks!

Came home to find the utility drawer hanging at a 45 degree angle. The culprit is this rear track bracket which had cracked in half. The drawer slide (the part attached to the drawer itself) reads "Unigrass 6600". No markings on the bracket other than "Left" and "Right". Dimensions for the openi ... (cont.)