Viewing all customer Discussions for:

Drawer & Cabinet

Need for drawers in kitchen

Bracket I am attaching a photo of a bracket that goes in the back of a drawer on one slide under the drawer, the cupboards were made in the 1984in sioux falls south dakota, I am wondering if you have any that are like this, mine is broke

This is a photo of a rear drawer guide I need 12 of them the best I can come up with is 2 1/2 wide 2 3/8 rail size 1/4 rail opening it resembles part 32-031 can you help Me with this

I have been looking for a replacement part for my kitchen drawer. The plastic socket is 3 3/4 inches long and the local hardware stores only carry a part that is shorter than this. I am hoping that you can help me find the correct part. Thank you, Sue

20" Drawer Slide.

I am trying to replace 1 1/4" rollers that have a metal axle (no ball bearings) that have worn out do to repeated use with heavy loads

Have 1 inch wood rails in good shape. 16" length. Center mount . Could use front &. Rear SWISCO type brackets or 16" length pieces. That would attach to bottom of each drawer . Can you help me out.?

I need to match the slider that I have pictured above. There is one of these parts in each of the four corners of each of the drawers of a dresser that I purchased from Crate and Barrel about 10 years ago. They were missing when I purchased the piece. I need about 10 of the sliders. I hope yo ... (cont.)

the wheel is a rivet style. Measures 7/16 diameter, 1/4" thick flat profile wheel, 3/16 out from side of the drawer

So this is a Lane dresser. The rail is on the bottom of the drawer. What is broken is the part that keeps the drawer from falling out when pulled open. It is a brown plastic part. Hope you can help. Many thanks

I'm looking to replace a drawer guide for an older home. The markings on the guide are PMC with a 1 right below it. The number 159 is also imprinted on it. It is white plastic with 4 holes on the side. A tag that was attached said it was a 159 Oxford. Would you have a replacement for that item? ... (cont.)

I have an older front drawer guides stop that is broken. Here are some picks.

Will this plastic soft door closer adapter work on a hinged bench top to help prevent pinched fingers? The top is 3/4" birch plywood about 36" wide and 18" deep to the hinge. Would two be required for this type of weight? I have 6 benches to do. Thanks.

The attached pictures are belong to the original part. Its the "side mount & bottom mount drawer slide mount socket". Inprinted on the bottom is "ADAR 8 LEFT". It is 3 and 3/4 inches long. I found a replacement part but it does not last and breaks easily because it is shorter and does not s ... (cont.)

I am looking for (2) window balance springs for a double hung window. One side broke but I am going to replace both. Following will be (5) pictures showing a "good" one that I took out of another window. Hopefully you will have the clips that attach to each end.

I'm trying to replace drawer rollers in cabinets that are about 25 years old. Metal rail system. I'm guessing a type of nylon, but they feel like hard plastic. Roller bearings, attached with rivet. 7/8 inch in diameter.

Hi. I'm trying to locate a white spacer that was attached to the inside wall of the pantry cabinet. It held up the sliding drawer. Name--MEPLA on bottom front and these numbers on the back: Right side--600.010 08.25 and Left side-- backwards 2 99 in a circle with

Is the needed screw included? If not, what size is required and do you sell them?

I have Hammary tables and need the "glide" replacement parts.

32-039 is ALMOST exactly what I need. The roller I have does not have the protruding axel (shown on the right side in the 3rd picture). The overall width dimension is 5/8". Do you make such a part?