Viewing all customer Discussions for:

Other

We need a new upper slider for our sliding closet door. The plastic has broken. I do hope you have it?

House ~50 years old. One must remove bottom piece of the door and then the wheels could be slid out the end.

My mechanism is so loose that the gears slip and the window will only open. Made by Truth The 2 short arms are marked 41010B & 31881 The 2 longer arms are marked 41016 & 41013 Only number on bottom of the housing that is readable is 09/17. We bought the house in 2016 so I do not think that is a date ... (cont.)

I bought my house in 2000. It was built around 1980 with double glass Pella crank windows. The cranks on my kitchen windows work to a point and then they seem to strip out and lose their catch. I have to get them to latchcl them from the outside using a ladder. That's a real pain. Anothert pain, is ... (cont.)

Hey all, first time experiencing this issue. We have a short-term rental and people are sometimes rough with the place. As a result, both of the main windows in the small apartment have come off their springs. The window was still in its shoes but I can't get the shoes reattached to the springs beca ... (cont.)

Need this replacement part

The small clear plastic endcap that attaches to the window has broken. The balance will not stay inside of the window unit because the endcap is broken. I have been able to identify the balance part number 2730 0. I'm not sure how to get the window out of the frame to be able to remove the small bro ... (cont.)

I could find no identifying names for window or the mechanism that locks/seals window closed. Photos above show the broken closure with the final picture, one that is working. You can see the plastic locking piece that is missing in the first picture. Thank you for any assistance. Kevin ... (cont.)

Metal part is 24 inches long. Marking: 22 3 D0 Caldwell Please help me identify the correct replacement part. I ordered S380-22 Option 2130, but it's about one inch too short. Thank you!

Photos attached for the locking door knob and bottom kick plate which I would like to replace in shinny brass. Also would like to replace the bottom door closer. Marking on inside of door reads "EMCO FOREVER DOORS" Serial #2894702.

How do you decide where in the channel to locate the pivot shoe prior to attaching the spiral balance?

there are 2 of these.length is 28 7/8 without plastic ends. item is for impact windows

We have (3) vertical sliding windows. Each one has a 1610 on the left and a 1640 on the right. The metal slide is 17" long on both. The 1610 spring is 5-3/8" and the 1640 spring is 6". Seem weird there would be two different types of mechanisms in the same window? Only one of the three windows ha ... (cont.)

Hello, Can you help me find a replacement part for this casement window operator.

Door 1 5/8

I need some tie bar guides that look like this one. I ordered a crank for the egress window awhile back maybe two years ago. there were no screws that came with the new cranks. the old ones were accidently lost do you carry the screws I need to install the crank?

Hello, we'd like assistance identifying the handle set that will fit our glass patio sliding door. The handle is broken, but the lock mechanism seems fine. Unfortunately, we cannot find any names or numbers, and nor do we have the manual. Thank you!

Code on spring is: 20 4 HP Caldwell

As shown in photo there is a #1 on the broad side of the part. It reads Del Mar Eng. Long Beach, Cal. Pat. 3.670.357. all pictures are of the same part. I would like to order two of them.

Brad here again.This is from my bathroom window. Another Kinro window. Window V.O is 27 1/2" x 36 5/8". The channel length is 17". That's the metal channel length. There's a serial # visible in pic 2. I would like to replace both sides.Thanks!Brad