Viewing all customer Discussions for:

Other

I am looking for an inside/outside door handle and lock set for a storm door made by Cole Sewell Registration 09110094538 0083

My banlace is 3/8 in diamiter and 25 inches long...The release latches say acorn on them . I am looking to replace all parts . Thanks Ed

Hello, I?m looking to purchase new double coil balances for my 36 x 60 single hung window. The coils measure half in wide. The pivot shoe is 1.25? wide by 1? tall by 0.5? thick. The coil springs have a T style locking end to attach to the pivot shoe. The coil spring holder measures 3? long by 1-1/8? ... (cont.)

The roller that I have is a corner post. The numbers that I have are B 221SSP, I'm guessing this is apart number

Viking crank out windows...I need the stationary bar for 2 units...Paul

Hello. I purchased Cole Sewell white double door kit Model #2410. They are still fine but I would like to replace the gold door handles on each one and the bottom gold kick plate if possible. Can you help? Thank you.

Hi, I have bfs windows and several channels need replacing. I want to make sure I order the correct replacement. They are 28 inches and have a 27-4 stamp with no other markings. It appears one of the side clips is missing and cord is broken. Can you help me? Thank you, Meg G

Hi I have a question....tried to use the website but not able to identify the end pieces on my channel balance. My channel is 20" long x 1/2" wide. Top plastic piece has two tab that extend to each side of the channel (1/2" long tabs x 15/16" overall width at tabs) and it is 1 1/4" long x 1/2" w ... (cont.)

I am looking for a replacement door knob for my old Cole Sewell strom door. The registration number is 12049896016 0009. Any help would be most appreciated.

I have two sash ballance springs that match your photos. They are stamped 26-3 and 14-3.The plastic end pieces match those in your typical picture of a 27"sash balance.Can you please tell me which Sisco part numbers match these stamped numbers?Thanks,Jim

my door is on a 1985 stardust cruiser houseboat the h track has a pressed in roller wheel with a roll pin the track is made of aluminum and is made so the top of the wheel fits thru a cut out in the h track mine is wollowed out where the roll pin goes in. can you help?

I have a measured 94" aluminum sliding glass door, brownish. It has 2 tandum roller assy that are both damaged. There are no identifying marks or names on the door anywhere. Our windows which match say Hallmark on the locking latches. Is Hallmark a manufacturer or just a series? HelpGarth ... (cont.)

I have tilt windows for cleaning with a grid which require 6 plastic pins to attach to the inside of the wooden frame. Where can the pins be purchased?

That information won't identify your roller. Really, only removing and inspecting the part will help. You can compare it to the single wheel and double wheel rollers in our selection.

Looking for a window lock

Good Morning, We would like to order 4 dozen each of the Coil Balance Shoe, Coil Balance Bushings, Coil Bushing Caps, and the Coil Support barrel. Pictures are attached of each part. Please confirm the size of the Coil Balance Clip. Per our measurements it is 1-1/4" and the coil support barrel i ... (cont.)

I'm not sure exactly which style of balance your cord came from. Could I see a photo of the cord, as well as photos of anything attached to the end of the cord? Does the cord come out of a box, or metal assembly of some kind?

need help on balances with double coil? coil

This part is attached to the table. The top slides through the piece

I am trying to find a replacement for my window channel balance. The identification number on channel part is 20 4 DR Caldwell; the length is 21". Thank you for any help.