Viewing all customer Discussions for:

Other

Please suggest replacement # for existing balancer 11600-17 and C 16 6#31 4 85. Thank you.

Appears to have missing portion 1/2" x3/8"

I'm in need of a sash balance for my windows. the weight of the window is 18 lbs the number stamp on the channel 21 4

I was closing my window recently, and I heard a snap and plastic pieces flew everywhere. It looks like the balance mechanism is a spring with a plastic tube around it. The first picture, Window Label, shows the label found on the window. Pictures Window 1-3 all show the broken spring. Window.jpg ... (cont.)

1 1/4 wide x 1/8 high this is the measurements of the opening for the slide itself on the back of the drawer the track it slide on to is about 1 and 1/8

We are having trouble locating this molding. Can you please help!

need new rollers for ppg herculite sgcc-295 15gh1190 ansi z971984 1/8u Due to weather im not unistalling my door until i receive new parts to be able to put the door back on

I need about 15 Melpa 510-356 Hinges. Can you help?

I am looking for the internal tilt latches. I'm not sure which to order. The windows I have are; 1995 certainteed vinyl double hung Bryn Mawr white replacement windows. roughly 3046 windows

Hi, The lock says made in New Zealand and has two capital i. On the bottom edge of the lock there are letters X A. Inside the handle it also says made in New Zealand. I need to replace the lock, handle and latch. Do you have these pieces? Thank you

Hi, I like to find out a part of a window. The part I'm talking about is at the center of the photo which is tighten by the screw. They are located on each of the top corners of a sash. Their purpose to hold the spring or coil casing(located on both sides of the window) as the sash is being pus ... (cont.)

I need 3 R0711L

I'm trying to find a way to cover my plants so they don't freeze again. We don't usually get freezing temperatures down here, but this year we did and my plant died because I had no way to cover them. One of the options I'm considering is using your brick hooks on the house and garden wall to hold f ... (cont.)

Need to replace the handle on my storm door. Registration Number 07059890143

My furniture is approximately 25 years old and the guides are worn out. They are dark brown, plastic, 2 inches wide, 1 1/2 inches deep, drawer middle bar 1 1/4 inches wide, three screw holes and the bar is metal. I would love to be able to replace them. If this information is not sufficient and I ... (cont.)

Looking for locking latch and keeper similar to those shown in photos. Mounting holes are 2" on center. Dimension from edge of latch (flush with window) to mounting holes is 5/8". (The tape measure in the one photo is actually measuring 2", but because of the angle of the lens, it looks like less; ... (cont.)

do these suction cups have a hole to place the stem of a small 4 inch decorative umbrella arm/handle?

Hi, Looking for replacement part for my crystal vinyl window. I have a broken plastic piece that connects the bottom of the window sash to the balancer used to raise the window. The first picture shows the broken piece the second picture shows the entire balancer and the third shows the only marking ... (cont.)

I am looking for replacement weatherstripping for 1983 Norco casement windows. There are two kinds of seals on each window. One is a white silicon 1/4" bulb seal with a flap on one side which goes around the frame. The other one is a leaf seal that is brown (color doesn't matter) and appears to b ... (cont.)

Ingenious mechanical design! You might consider future product labeling to lead homeowners directly to your home page featuring how-to videos. I first encountered two "fallen" balances left disconnected by the previous homeowner and I could not for the life of me figure out how the hell they w ... (cont.)