Viewing all customer Discussions for:

Other

Need identifying the part number for attached pictures

I need the piece that has the upper part of the window that holds the balance. That piece, black, is held with a screw and has one on both sides of the window.

Vinyl beading for window

I currently have 7 of these in my cart but I threw away all of them plus the screws.I kept 1 without screws to get correct size. the 26-275 are the right size. Do you know if you have any white painted screws on your sight that fit these?

Hey I was wondering if your part 32-025 could also be a reliable substitute for this vintage cabinet drawer bracket ? The 32-025 replacement has a hinge at the top that fits the back of my cabinet which this 32-094 does not have. I submitted a picture of how the hinge looks like on the original par ... (cont.)

I have a closet with a couple of these rollers, which have failed. 1/2" offset; 1/2" diameter wheel round wheel surface. What do you have for this roller?

I snapped a door handle and I'm trying to identify the part and manufacture. Haven't found any markings for the manufacturer. When I type in the only two number I can find nothing comes up. Need help finding who makes this door and door handles.

Lookin for a low profile bottom rail for 2 sets of Stanley mirrored bifold doors. Vintage around 1999 or 2000. Each rail was 1" × 1" x 60" long. I need a low profile rail after installing a new floor. Will the 21-455 work? Does it come in any other color? Will I need to order extra parts. Thank yo ... (cont.)

I'm looking to replace these window sashes. They have the metal piece at the bottom and string that attaches at the top of the window frame. See picture. I would like to know what parts are needed to replace the broken ones, please.

Hello I am trying to find the correct rollers for my screen door. I got the screen replaced, the hardware store gave me rollers that were too large I was able to get a picture of my neighbor's screen door I believe the screen is an American Craftsman model.

I placed an order and had to return it. I had got the wrong part, I am trying to see if y'all could help me identify this window balance. The ones I had ordered was 9/16, they were too big. 28" was the correct length, just had the wrong diameter.

nneed 2 anderson window crank assembley's 1 LEFT ,1 RIGHT. # on crank body is7198-17 the single arm is aprox 10.5 inches long from the center of the pivot hole to the end of the arm, not countig the plstis slide

This is a 3' x 6' message board lock that I am trying to find a replacement for. The message board is metal framed and has nothing wrong with it but the lock. Any suggestions?

Looking for handle replacement Door ID# is 030101901700020.

I need the right side bracket and hope the photo is good enough for you to decide what I need. Please let me know if you can help me. Other then the shape of the back the measurements you have on your diagram from what I can tell are the same as 32-146. I was thinking 32-012 looked like a clo ... (cont.)

Hello, I have a patio door that the latch fell into the frame as I was trying to take it out and see what's wrong with a hook. Please help me find the proper latch. The fitting is only 2 1/2 inches in length and .5 inch wide. Please take a look at the pictures for measurements and more information. ... (cont.)

spring locks are broken to allow window to hinge open for closing. they are recessed into the window so not sure how to get them out for replacement. they are 2 5/8 x 5/8

Looking for a tilt latch replacement for a jeld wen window

Looking for a plastic weather seal that goes at the top of a double hung window. Wind is from the mid90's. Also looking for any other reubild parts you might have for these windows.

Hi, I am looking for the End clip (grey looking in the picture) that attaches to the ends of the window joiner. It is a Silverline vinyl double hung window with an attached transom like window extender at the top.