Viewing all customer Discussions for:

Other

Had one of my channel balance brake it sprung to the top and the other is on the bottom and a plastic tab fell on and the cord is hanging out. Looking at it it has the following numbers printed on it 16-12 KH5 CMC 50

Several of my upper sashes are missing weatherstripping. Stuff I bought from Home Depot doesn't work because the tab that is inserted in the channel to hold in place is much too long. I've attached photos. The weatherstripping in place on the bottom sash is foam and has a "C" shaped profile, as ... (cont.)

I am looking to identify the following lawson block and tackle replacement park. Appears to be 29 inch length, 1/2 inch channel depth. Winged hardware. Stamped 28B Q

Hello, I need a crankcase operator for my window. The crank is on the right hand of the window. Can you let me know which one I need to buy? I see you have it on your pictures on how to order, but I did not find it in the items I can order.

Need help to identify part for split arm operator. It is surface mounted in Anderson casement window. It is make in USA and has some numbers on the bottom side(45352, 31897). Manufacture date is 09/29/2002. It is mounted by 6 screws and all 6 screws are on one line. I need to replace one left hand ... (cont.)

Color, White, no mounting holes.Dimensions:2 7/8" length, excluding tang.11/16 width.7/16 height.This photo was taken from the tilt latch on the Right side of the window.When identified, I will order a minimum of 4 sets ( right and left latch assemblies.)

The door is a sliding patio door (one door stationary) circa 2020. I am trying to replace the weatherstripping that is on the door frame (not actually on the door). I can not find any serial numbers to help identify the door. Do you have a suggestion on which weatherstripping would work? ... (cont.)

Greetings..Id love to purchase a replacement locking mechanism if available ?

Our dog pressed against the window and broke the crank mechanism. The windows are about 20 years old and purchased in Houston, Texas.

Do you have this one? I need 2 units.

I am looking to replace the bottom gasket on 6 windows; 4 will require 43 inch pieces. 2 will require 33 inch pieces.

Windows are exterior crestline casement windows replaced anywhere in the mid 1990s to early 2000s. Weatherstrip has a foam bulb. Rough dimensions are 5/8" total length, 1/4" width (foam), base extension (insert) 1/4". If you need additional information. Please let me know

Please see my photo attachments (2) of these window side clip retractable accessories available for repair

The weather stripping on Pella door matches the spec on the 58-181 but doesn't do a good job at blocking drafts. Can you recommend another that would fit and might seal better?

I do not know the manufacturer of my storm door. There is R 5 marked on the back of the right hand latch, no mark on the left latch. I need both latches and springs.Frank

Can you please give me a part/model number to replace the Brocken latch lock shown in the attached picture. Also, does it cover in warranty? Thank you for your help!

Trying to repair several screens by replacing the plastic inserts in the corners. They are approximately 1.5 inches long on each side, fit into a slot that is 3/8" by 3/16". Pictures attached.

I have a 1986 age ranch with casement windows. many need new weatherstripping. the weather stripping fits into a slot on the frame. I have attached photos of the installed and uninstalled frame and also the existing stripping. The side weatherstripping is different than the top and bottom. ... (cont.)

need replacement weather stripping for neuma patio door. only numbers I have for this door is D305681-Swisco Installed in 2019 Order #2186562

the spring and the part that latches into the window itself are missing the window part is in place and it is of the standard window latch that fits into the balance. the window measurement from top to bottom is 54 inches