Viewing all customer Discussions for:

Other

There's 2" distance between mounting screws on interior latch -- the handle is approx.4" by 1 3/4" -- hope this helps.

Can you give me the correct replacement balances for the left and right side .

Need a right-hand snap-in mortise tilt latch marked R-24. Matching left side is L-24. Vinyl double-hung window. Dimensions: 2-5/8" long × 9/16" wide × 1/2" deep. No screw holes.

Need replacement balance. Stamp on existing part is 26 4 AN Caldwell

I am looking to replace the locking mechanism that goes with the lock set "Legacy Keyed Handle Set, 3-15/16" (1-1/8" to 2-1/2")" The mechanism is missing, so I don't have the part that needs to be replaced. I do know that the screws on the door are 4 inches apart. Can you help?

36 4 A1 stamp on balance. I believe Series 378

i am looking for the pella lock stile weatherstrip for the designer series sliding glass door. this seems like it would be a common replacement as it is on the edge of the moving door but i have not been able to find a replacement. the photo below shows the bulb is 5mm x 5mm and the u shaped width ... (cont.)

Shoe and coil support are both 1 1/4" wide. shoe is 1 1/2" tall. coil support is 1 3/8" tall. coil is 1/2". Window weighs 18 lbs. Window size is 25 1/2" wide x 26 1/2" high. Lower window. Double hung unit.Tilt.

Aproximate dimensions: Width: 3/4" Height: 1 7/8' Length: 3 3/4" on top 2 3/4" on wheel edge (bottom) Steel concave wheel diameter 1 1/4" This is a metal frame Arcadia door, not sure how old it is but chances are older than 2000.

The 3 coils are marked 2 are 6z and 1 is 5z. The plastic housing is shattered. I will need the comple unit for both sides of the window. Also need instructions on how to remove and install.Pat

Hello, I'm trying to identify the correct replacement mortise lock and matching handle for the original sliding patio door in a Redman manufactured home built around 2002–2008.Unfortunately, while removing the handle, the original mortise lock fell down inside the hollow door stile and cannot ... (cont.)

Window is a Prism by Simington. Approximate 2015 installed. I need the balance

Hello, Could someone please help me figure out which channel balance I need for a Philips 91S Non-Tilt window? The broken balance slid out by itself, so I couldn't get a picture of it installed, but I have attached photos of the removed part. The metal channel has a stamp that reads: "25 4 CALDWELL ... (cont.)

Hi, I'm looking for a tilt window pivot lock shoe. The dimension I'm looking for is 1/2 inch think, 1 inch wide, and 2 inches long. The length probably doesn't matter much but the thinkness and width needs to match the window. I looked through your catalog but didn't seem to find a match. Could you ... (cont.)

Hello, I need to replace the pinion in this door handle. Do you sell just the pinion or do you sell replacement door handle sets? Thanks you! Andy

Hi I have some 20 year old Tempco vinyl windows, some of which need a little TLC. I'm looking for a set of tilt window latches and a set of vent stops, both in white. I'm having issues finding the parts locally and since the brand is no longer in business, I don't really have anyone to reach out to ... (cont.)

The window is Milgard. It measures 14 5/8X 42 3/16. Do you have a replacement set?

I need the lock and the latch for a sliding glass door. I do not know what the manufacturer is. But I do have Photos of the latch and the lock that I will send to you

Hello, I need some advice on what I need to fully replace these sash balances on my windows that are all cracked. The window now falls out freely when I open/slide them up.

I'm looking for the keeper for this lock. If not available, I would like a replacement. That will fit