Viewing all customer Discussions for:

Other

Hello I hope you're doing well. I've looked on your website and I'm still not 100% sure which one I need to order. My windows are about 20 years old and do for some new weather stripping at the bottom of the window. Sending pic any ideas? New windows? Thank you,

the part that is inset into cabinet door is 1-5/16 or 1-3/8" Cabinets are full overlay

Hi, could someone tell me what parts I would need to get these wood frame windows working properly? As you can see when I open the window the strings are loose and will not wind up to hold it open. Thanks!

Hi, I have an older house with some original metal windows. The windows are either very hard to open or they will not stay open. A couple of them are missing latches. Can anyone help identify what kind of window this is and what parts I may need to get them working smoothly again? Thank you ... (cont.)

I have 6' with 1 in. Sliding Screen Door Tension Spring with Concave Rollers. My question is can I change that out to 1 1/4' roller? I have a little slop on the top of the door. Thanks George

I have the length measuring at 44 1/8" and the shoe is 1 1/8". I believe I have the series 390. We would be looking at an estimate for 12 of these. One has 4240 and the other has K 4330. Even though I have two different stamps, my technician is requesting them all be the same length. As for the m ... (cont.)

The right sash string tore and I can't keep the bathroom window open. The glass shows Anderson MC 90-2 XL. The left sash string is missing.

Hi We are in need of 2 30 in window balances shown in attached pictures.I did not see these listed on your website. Let me know if you have a replacement. Thanks, Gary

I need a couple of rollers for my patio door. Pictures are included.

Looking for a rigid glazing bead for Windsor Windows Legend series (their part no. is 2390002); even a close enough replacement would do. Thanks

Looking for a replacement crank measures 8"

It is stated with CARE-FREE into the plastic. It is approximately 4" x 1/2". This in on a vinyl door on our porch that was installed in the early 90's. It is a double door and 2 of the broke on the same window - right and left. If we can find the right ones we would purchase 2 right and 2 left. ... (cont.)

Hi, I have an exterior door which had the handle break and has a loose lock. I am hoping to replace the handle, face plates and lock and not have to take out/replace the mortise lock that is inside the door (but will if necessary). I included pictures showing the dimensions of the lockset and hope ... (cont.)

18" x 5/8" x 1/2" metal track only not including nylon tips has a 17 4 stamp

Windows have M/M logo on locking device. I believe they are original windows installed in 2006 when the house was constructed. I would like to get 2 of these as I will plan on replacing both on the same window to keep the window in balance better. It is a 1/2" channel with a 27" length overall. ... (cont.)

I need to replace 4 of this top sliding guides for 2 acme closet door. I attached 2 pictures of the same item (different angle). Please advise which part of your catalog I should order.

Can you identify this part? The pivot lock screw is 1-3/4" long and have a hole in the top where the string goes through. The pivot lock rides in a channel with a raised area in the jam liner. This is clearly visible in the picture. The jam liner has a 9000/9500 Walter label on it. Do you have a rep ... (cont.)

entry screen door protector plastic

Need a dummy knob (lever) for 82-399 for French doors. Thanks

My balance is stamped with BSI 20E It is exactly 1/2 inch square and exactly 20 inches long. I need at least four of these kits Picture WS1 is the locking terminal. Doesn't have to be an exact replacement. I just need something that will fit in my window and function correctly.