Viewing all customer Discussions for:

Other

Hello, Can you please assist me finding a key lock for my basement slide door ( I want to have to option to lock it with the key from outside). The mortise lock number is : PAT# 6.264.252. Thank you, Abdullah

in the photos the bottom sash needs balance in side window is 491/2" top to bottom sash is 25"x21"1/2" the channel on the side of the window is 3/4x3/4 top sash is 27"5/8 fixed

Have not been able to find it with the proper ends

It's not the latch locks attached to the sliding glass window part but the straight piece that the locks latch into behind it. My nephew stayed with us and apparently broke it so I can't even lock my sons window anymore. I just replaced this window with the over $250 window and my nephew who's a tro ... (cont.)

They say truth on top of the arm 4 3/8 hole to pin

Need to replace 2 crank assemblies. Teeth are striped on right and left windows. Thank you for your help.

The First Two picks are the Anderson Casement, Manufactured in 6/2000. Has #1361460 on it. I need both left and right. Second set of photos is a Anderson awning window, I would need the crank mechanism, it is stripped out. I belive the casement is a 400 series window from what I remember. Do you nee ... (cont.)

Need to replace 12 inside pull and 13/23 outside pull with key lock

Coil balance series: S210 Sash-weight: 25 Coil-stamp: 12 Quantity: 2 Comments: Old Sears replacements need both left and right if there not universal

Hello, We had an incident and cracked the mirror on our bi-fold door. Is there anyway to order a replacement panel or mirror?

28 4 AO CALDWELL window balances which one should I order ? bottom plastic piece is about 1.03" deep, 0.56" wide, and 1" long top plastic piece is about 0.725" deep, 0.575 wide, and 1.25" long

Have some kk window cranks that are stripped from windows that are in good shape. Most likely from late 80s. Would like to order one of the right one just to be sure. Before I order 6 more. Let me know if you have something that will work. Thanks!! Ken in Wi.

the length is 26.5 inches, width is 1/2 inch. the stamp is 26 4 it is the Milgard manufacture, the window was installed around 2007 I may need 10 ~12 pieces of balances thank you so much Sherman

Hi, Can you please help me identify my window balance? Markings show BS1 29.

We have the Andersen sliding door (late 90s era) with the handle and deadbolt shown in the photos. The darker image is outside looking in, brighter image is inside looking out. Interested in installing a locking key lock that can be un-locked / locked from the outside. Would the LH 82-316 lock work ... (cont.)

Hi, I'm just moving into a place that has a missing deck door handle. I was told you could help perhaps identify the part and even, possibly, supply the part. The pictures above shows the slot for the handle in the front of the door, and corresponding latch on the frame. The slot is 6 5/8" long, and ... (cont.)

Hello, I am trying to replace some pile weatherstripping in my Steel sliding door, and am having trouble Identifying the type and pile. Any help would be greatly appreciated. Thanks.

Hello - I think I need a 90-180. However I wanted to double check. The two holes are ofset 3/8" from the edge and 2 1/4" apart. See attached pictures. Looks like the part # might be 8303 from Alpine. Thanks

the writing on the sashe says 10 5 pt amd bs1 the measurement on the sash is 10.5 long and .5 wide thankyou

Approximately 1.5"x3"x.75" (HxWxD). Wheel is 1.25" diameter. Marking on top says "ASTR BEC OMCO" in a circle