Viewing all customer Discussions for:

39-102 T Handle, 11/32"

Does 39-195 work to replace a 1992 Marvin casemaster windows lever handle.

I am looking for Extra Heavy Duty Crank and Rail to replace the existing crank for steel window which is very old and very stuck. We replaced the original cranks with the ones you see in the photos, however most of them were broken because it is not strong to open heavy window especially when start ... (cont.)

I have Hurd windows from mid 80 s. With crank handle. Would like the t crank handle instead. I was once told it is "operator t crank handle....#092684 I would like bronze. Thanks for your help The pictures are my current, old cranks, but I would like to change to a t handle, so blinds don't ca ... (cont.)

I would like help with replacing the pictured crank handle with a smaller profile T-handle ( I need 3) so vertical blinds don't stack on top of current crank handle when lowered. I don't know spline size. Also, the sleeve that goes behind the locking latch, several windows are missing these. ... (cont.)

I need additional versions of these in white. I have tried 3/8 inch handles but they are too large to fit the crank shaft. The shaft is toothed, and around 1/4 inch diameter. The windows are from 1986/87.

I'm trying to find a t-crank or hand knob for a weathervane casement. I've found a bunch of these t-handles but my problem is that I don't know the size of the spline.

New shutters have my Awning window crank hitting the frame. I tried a Jalousie T handle in size 5/16 (too small) and 3/8 which now hits the housing instead.what can you recommend? Is there a T handle that will work. The windows are from 1978

I am a Handyman, trying to fix this window for my customer. There are no markings on the window and, it is not frozen or painted shut. It looks to be a standard window with standard parts. The Tee handle spline is stripped out but, the window cannot be cranked open using vise grips on the operato ... (cont.)

Just moved in. All windows have the attached crank, with 45054 imprinted on the inside, no other identifying names/numbers and nothing on the window component either. Want to replace the cranks only with a T-crank, same color, same screw whole size. Can you help?

Gentlemen: I have Semco products in the house; need to replace some regular cranks with T handles but don't know if I need 3/8 inch or 11/32 or whatever to do so. Iam not presently at the subject home. Any idea which would fit Semco, pre 2005 ? thanks

Dear Swisco, We have Integrity windows by Marvin, with Truth Hardware operating mechanisms. The post for the window crank has 11/32

The markings on the window appear to be SNE IGCC (r) CBA IGMAC WI Thanks!!

What single arm operator works with the Truth Folding Handle with Cover, 39-375?

Hello I just purchased a home with 15 casement windows which are opened & closed daily. The hole in the existing handle appears to be 3/8 inch. As you can see, the small area makes this a long process & usually leaves my blood behind. Also, my fingers aren't strong enough to open the window entirel ... (cont.)

Hi, I have some Milgard casement windows with hand cranks. We recently put in plantation shutters. One of the frames of the shutters is not allowing the crank enough clearance. I noticed that another window in our home has a different type of opener, a knob. See below. Could I get one of those to re ... (cont.)

Sorry I don't have any other pictures of this one. It was sent to me from a job site. Could you possibly identify it or something close? Thank you! -Suzanne

I have three 1986 era Hurd casement windows with traditional gold tone Hurd cranks for which I have ordered new window treatments (dual roller shades) I would like to replace the existing crank handles with T-handles so the roller shades will not interfere. The spline bore looks to be 3/8" inn ... (cont.)

i have your crankout windows i need to replace the cranks to tee cranks for my new blinds. I'm measuring 11/32nd for he opening. What size should I order? Thanks

I have a window in my kitchen with an existing awning window lever operator (see attached photos). The handle for the lever operator will interfere with the new faucet that I will be placing directly in front of the window. As such I thought it would be a good idea to change it to a roto gear window ... (cont.)

I have K+K casement windows, and I need to replace some cranks. How do you determine the proper size crank? I know I can take it off and measure it, but exactly what needs to be measured? Thanks