Viewing all customer Discussions for:

55-156 3' Wenco Snap-in

Double-hung wood windows from LP in 1978. Looking for glazing bead that is 5/8" on both sides. The two small lips are each 1/8 inch. The angle is probably 60 degrees (upside-down vee), but might have been closer to 90 degrees when new. Cannot tell. Do you have this in stock -- or suggestions wh ... (cont.)

I believe this is from a Champion 3050 window

Please help identify this part

Please see attached photos of the snap in glazing I have in my casement windows. Please identify and suggest a replacement if possible. My windows were manufactured in 1975 and have know identifying marks or numbers on them.

Do you have a suitable replacement? The glazing is from windows installed in 1978. I have no further identifying information. It is possible that the brand is Crestline, but I can't confirm that.

Need replacement parts for a gliding patio door of unknown make and model. Circa 1988. Looked all over on all sides inside and out and can't find any markings except for the glass: Herculite K and PPG. 8' wide custom wood gliding patio door including 4' slider and 4' sidelight. Note the plastic or v ... (cont.)

Trying to find this style of beading.

I have been redoing a house my father built and I am having trouble finding replacement exterior glazing beads for the weathershield casement windows. The original are vinyl but some were replaced with aluminum around 1994. I spoke with weathershield and they don't make them anymore. Does anyone sti ... (cont.)

I'm needing approximately 10' of snip-in glazing for a MW Window. The window is a wooden double-hung circa 1995.

Trying to find replacement snap-in. It appears to be very similar to the Wenco on your site. The overall height is 7/8" rather than the 3/4" of the Wenco. Also, the one that I have has a small 'bulge' at the bottom of the main spline. Additionally, the kerf spline on the Wenco appears to be in t ... (cont.)

Wondering if you had or could help ID these glazing beads Thank you, Kimberly

I need replacement bead for the attached. This is for wood frame casement windows manufactured by ROW. Company is no longer in business. Original beading is grey, but I would prefer white. Thanks You, Ray

Trying to find replacement glazing bead. Vinyl window - no markings. Brittle and broke when trying to remove to replace IGU. Any suggestions based on the picture? Thanks Karen

Dear Sir, I try to match my old bead to your part and so I can make an order. The height and width of my old one is about 1/2". In terms of the shape, my old one is very close to your 55-156. The height of the 55-156 is 3/4". Also the side flange of my order one is a little bit closer to the top ... (cont.)

I am doing some windows that II need some glazing strips that looks like part #55 156. We are using 7/16 Ins.glass. That little tab on the backside has to be 1/4" from the top of the molding We did get some glazing strips, but its falls 3/8 down from the top so it goes past the slot to hold in p ... (cont.)

Our home (built in 1983)has some original wooden sash windows made by Hurd. We need to replace some snap-in glazing. The current snap-in glazing is 9/16" by 15/16". Part # 55-156 looks close but ours does not have the "hook" detail. Would #55-156 work?

I have wood-framed double hung windows (brand unknown) that are about 40 yr old. The snap-in glazing is getting brittle on some of them and I was looking at your Capitol Snap-in Glazing 55-030-6. I then noticed your identifying service and ..here I am. Thinking about purchasing just a couple of piec ... (cont.)

I have older wood MW windows in my house that were installed around 1985. Recently I had one break and needed to replace the double pane insulated glass in it. The glass is held in by a plastic L shaped glazing bead very similar to your Wenco snap-in #55-156-6. I removed a sample piece and it is alm ... (cont.)

We have wood frame windows wich use a snap-in glazing to retain the glass #55-030 very closely matches (within a 1/16. Any experience in this type of application?