Viewing all customer Discussions for:

10-100 3/4" Flat Shower Door Wheel

Hello, I need a few replacement wheels like this, can you help point me to the correct part numbers or alternatives? Diameters are: 1 inch 3/4 inch Thanks.

i need replacement drawer rollers - 12 large ones and 12 small ones. they go in a (45-50 year old) 4 drawer office cabinet made by steelcase (i think). i have included measurements (using a digital caliper) of the rollers. they are similar to SWISCO item # 32-039. however, the item # 32-093 do ... (cont.)

I need to replace the top and bottom rollers on the captioned door (lock side). Please see the pictures(4), including the manufacturer's tag on the door. The 3/4" dia. roller is the top roller. Your attention in this matter is appreciated.

Do you have a roller as in the picture?

The roller on the opposite side of this drawer came off and disappeared during our recent move. Diameter is 3/4". Width is 3/16" at the rim and 1/4" at the hub. No visible markings. The track and the roller seem to be pressed or riveted. I'm sure I will have to improvise the attachment. I needed a ... (cont.)

These little rollers are on the top of the patio screen door. The slider screen hangs on these little rollers and is kept in place with 1.75 " x 3/8" plastic guides. I need both.

Hello, I have a 20 inch drawer slider, that the roller has broken off the part of the slider attached to the cabinet frame. I tried to replace the whole slider, but the drawer portion of the slider is incorporated with the sides of the drawer, so can't be replaced, and did not match the new slider. ... (cont.)

Hello I am trying to find the correct rollers for my screen door. I got the screen replaced, the hardware store gave me rollers that were too large I was able to get a picture of my neighbor's screen door I believe the screen is an American Craftsman model.

Looking to replace just the one shower door wheel. Do you carry just the wheel.

Roller dia 19 mm c 6 mm thick, And 12 mm dia x6mmthick

I am looking for replacement drawer slide for the provided photo item. Also, individual rollers, if possible.

I have a broken wheel on the right side of a kitchen drawer. The wheel appears to be riveted onto the side of the metal side of the drawer. The underside of the metal is stamped "UNIGRASS 6000". the side of the drawer is 20" x 3 1/4". The broken wheel is 3/4" diameter.Can you help me? ... (cont.)

Please let me no if you have this part

the plastic wheels at the ends of the rails are broken. Is there a way to replace just that paryt. if not, where to get the rail. Thanks p.s. pic is upside down, obviously alan

This is standing 1 1/8 the base is 2 &1/2 between screw holes 1&3/4 Trying to find this roller for my bathroom slide door i Google A-s3937 and that came on your page I think the 10-152 will work but i may have to change that side out because mine looks a little higher it's 1 and 1/8 height the widt ... (cont.)

As best as I can measure, the post is about 1/8" wide, the roller wheel is about 3/4" in diameter and the width of the roller is about 3/16". As you can see, the roller is held on by a rivet or a cap. The photos above show what the roller looks like and what the post looks like. I would just replace ... (cont.)

My kitchen has a set of metal Beauty Queen kitchen cabinets/drawers/double sink from, I believe, the 1950's. Evidently a number of the rollers for the drawers had broken before I lived there...there are a few 'replacement' wheels that have a metal body attached to them which impedes the drawers fro ... (cont.)

I am looking for new slider wheels from 1950s era closet doors. The rubber has warn down on many as shown in picture.

2.steelcase drawer nylon roller 23/32 in diameter by 21/64 wide shaft hole 9/32 with o ring

I have a cabinet draw and looking for a replacement wheel. The wheel is 3/4 by approx 1/8 to 1/4 wide