Viewing all customer Discussions for:

82-008 Patio Sliding Door Handle, 6-5/8"

I need to replace the entire inside mechanism for my sliding glass door pulls I have both the inside and outside parts I have the following from Miami, FL OUTSIDE DNS Industries 13/23 OUTSIDE PULL -1400 SERIES INSIDE DNS INDUSTRIES 12 INSIDE PULL -1400 SERIES I NEED THEM INSIDE LOCK PARTM ... (cont.)

To Whom It May Concern: I am looking for a specific part to replace for my parent's house's sliding screen door. The screen door lock is broken, however many people have told me that the Marvin screen door is hard to replace, so I am trying to locate a place that can just sell me the locking part ... (cont.)

I need to replace this lock for a glass sliding door, but I don't know the exact part number I need to order from your company. Thanks in advance for your help. Juan C. Marulanda

Hi I am looking to replace my DNS Industries 12 inside pull 1400 series and I would like to know if the 82-008 is a match.

I need 6 replacement Daryl sliding glass door locks, non-keyed. The existing Daryl door lock overall dimensions are 7-3/8" long x 1-1/8" wide and a screw spacing of 6-13/16" center to center. There are 2 part numbers - on the exterior part is P/N 15047 and on the interior part is P/N 15049. Any help ... (cont.)

Hi. I need to replace the sliding door handle of my balcony. My door close in the middle, and I need to change both sides. The lock of the door is in the right side, so I need to know if the lock section in your Product Code: 82-008, Daryl Patio Sliding Door Handle, 6-5/8", can be switch or change ... (cont.)

I need tow kits

I am trying to identify the part number to replace the lock on an aluminum sliding glass door that was made by Atrium, Model #M 2-5M SGD.

need to replace a patio door lock that looks like an 82-008 except the width is 7/8. Any suggestions?

You carry a product that is very close to what I'm looking for Daryl Patio Sliding Door Handle, 6-5/8" Product Code: 82-008 -- however, it is not wide enough. Do you have basically the same item 1-1/8" wide?

I have a lock made by DNS marked 23/15 That is a Daryl lock look alike. The problem my lock has a black plastic spacer around the inside between the frame and the lock. It is about 1/8" in thickness. It is cut out for the lock in the center. Does anyone make the spacers anymore?

I am another homeowner with a similar glass door that needs a new inside pull. I think that your 82-008 is correct in size and shape with the exception of an extended piece on 1 side of mine that is missing from yours. I wonder what you think. Also I wonder if there is a store locally that ... (cont.)

I have a 4 panel, center-open patio door in my 1970-era high-rise condo. Your 82-008 handle is the correct dimensions, but I also need a handle for the partner door (without locking mechanism). What do you suggest?

Part says DNS Industries 16 inside pull standard Tried to replace with a assembly from slide- co which mounted fine but would not lock. locking lever about 1/2 inch lower.

House was built in 1969. Locksays LOOK products Inc. patent #3321227. actual locking mechanism is on top approximately 1" down.

Re:- patio door replacement lock. I have a DNS industries 'outside Pull' which has a 13/23 stamp on it and on the 'inside Pull' has a 16 stamped on it. Do you carry this?

I need to replace a Patio Sliding Door handle. Would you please see if you have what I need to get this fixed? Length: 7 7/16" Width: 1 3/16" Hole to Hole: 6 7/8" Identifying piece on the Door handle is "Daryl" and #s on the interior are 15049 for inside piece and 15047 for outside piece. ... (cont.)

I am looking to replace the handle and lock on an old sliding glass door. The door does not lock. I've attached photos and measurements. Photo 1 - It is approx. 6 1/2 inches from the top screw to the bottom screw on the handle that opens the door from the inside of the house. Photo 2 - It mea ... (cont.)

It looks like the Daryl 82-008. Can I replace it with a 82-008K. Also, what is your return/refund policy. Thanks

Hello, I need to know what would be the equivalent of the subject part? My door is 1 1/4 inches thick and the distance between both mounting screws is about 7 inches. Thanks for your help, John