Viewing all customer Discussions for:

82-008 Patio Sliding Door Handle, 6-5/8"

I need to replace this part (DNS Ind. 12, inside pull 1400 series) I believe I should order 82 008 Daryl Patio handle. 6 5/8 is correct. Can you confirm that this part is the correct replacement? Thank you. Tom

Looking at the 82-008 as a replacement for my DNS 1400 series. With the tooth pointing down, when locked, my locks tooth can be lifted off the keeper. I could shim about a half inch at the top of the door to prevent this. (suggestions appreciated) I'm also wondering if the 82-002 comes in chrom ... (cont.)

Weather strip on glass.

What is the difference between these two mechanisms/part numbers (other than the price!)???

Daryl patio rama 300. Numbers on the lock is 19053 and 19103-BL

DNS Industries 1400 series lock I am wondering if you carry it

I received 5 Daryl Patio sliding door Handles, 6 5/8" (82-008) and 5 Patio Door Lock Keeper,3/4 " wide from you . While the handles fit into the door nicely, they don't latch to the door keeper - even with moving the keeper up and down. The frames are by Al-Can which I think is out-of-business. I ... (cont.)

nee to replace a patio door lock made by dns industries series 1400 12 inside pull

If it was actually two sliding glass door sliding into each other not a wall would you need two different parts or two of the same? Is there a left and right model?

Looking for a replacement of this lock

Good morning I recently bought a number of Daryl Patio Sliding Door Handles (6-5/8" - part # 82-008) and are wondering if you have a matching door handle (a dummy handle) for the right side (viewed from inside) door. It has no working parts, is not part of the locking mechanism and is only attach ... (cont.)

Hello, Need to replace this item. dns industries 16 inside pull standard Thanks, if you can help me out. Leonard

THESE PARTS ARE ON A 1986 SEA RAY REAR SLIDING DOORS. 1-DNS INDUSTRIES 12 INSIDE PULL 1400 SERIES 1-DNS INDUSTRIES 12 INSIDE PULL 1400 SERIES 1-DNS INDUSTRIES 12 INSIDE PULL 1400 SERIES 1-DNS INDUSTRIES 13/23 OUTSIDE PULL 1400 SERIES W/KEY (HAS GASKET) CAN HAVE IT SHIPPED TO HOLIDAY FL ... (cont.)

Marked DNS Industries Miami, FL 1 1016 Japan 1014-2 7-3/8" by 7/8" appoximaltely pictures included Your Daryl 82-008 looks like a match Need 2

Good afternoon Madam or Sir I recently purchased an 82-002 sliding door latch it does not latch it is to low. Is there another latch the same length that latches higher. I have attached photos. I live in a concrete building. The jam latch cannot be moved. The old latch is chrome. thank you. ... (cont.)

I am trying to locate a lock set that resembles your part #82-008 that is made for a thicker door. none of the measurements listed pertain to door thickness. Most of these style locks fit 1 1/4" door frames. What I'm looking for is, I believe made by PGT I think to be a 1 3/4" frame. The latch on wh ... (cont.)

I have taken a few pictures which I hope may help your research folks to find a best match. As you see, the name on the original lock set is CROWN. The hole/opening in the door when this lockset is removed (see photo) measures 2 cm x 18 cm.

I need to replace the entire inside mechanism for my sliding glass door pulls I have both the inside and outside parts I have the following from Miami, FL OUTSIDE DNS Industries 13/23 OUTSIDE PULL -1400 SERIES INSIDE DNS INDUSTRIES 12 INSIDE PULL -1400 SERIES I NEED THEM INSIDE LOCK PARTM ... (cont.)

To Whom It May Concern: I am looking for a specific part to replace for my parent's house's sliding screen door. The screen door lock is broken, however many people have told me that the Marvin screen door is hard to replace, so I am trying to locate a place that can just sell me the locking part ... (cont.)

I need to replace this lock for a glass sliding door, but I don't know the exact part number I need to order from your company. Thanks in advance for your help. Juan C. Marulanda