Viewing all customer Discussions for:

95-112 1/4" Square Cut Corner, White

Do you have 5/16" x 3/4" corners that will fit my screen frame? As I repair torn screens, I suspect that I'll have several that will break when I remove the screens because they're so brittle.

Hi! Looking fora replacement screen corner for this screen.

1 3/4" length both ways, Corner square is 3/4", width 1/2", thickness of sqare part 5/16", thickess of slide in part 1/4"

Do you guys stock these. Casement window screens. no markings.

Need assistance with finding theses corners please

My screen Frame for my pet window is a 1/4 inch frame for a storm door/pet door. I will not replace the door because the 2nd generation wildcat paws at it and I will or a pet door after I take this door off and make the modifications to the door.

Hello. I am in need of some Replacement ones. Can you tell me what the cost is?

My corners are 3/4"x3/4" and the width is 5/16". The part that goes into the frame is only 1/4" thick and 1/2" tall. Need to know if you stock them in white.

Looking to replace my window screen corners. Attached are photos showing the old screen corners with measurements. Would 95-112 work. Also the springs shown on your website. Would any spring work. See old spring in image attached Thanks for your help

The aluminum frame measures 1/4 " x 1/2". I need the plastic corners that fit inside the aluminum frame. The plastic part that inserts into the frame is 19/64" x 13/64ths "

Hello!! The corner is 1/4" by less then the normal 3/4". I purchased ones with pull tabs 1/4" but to thick for frame & seems to be about 1/8 to wide for about 1/4 inch to much for screen to fit back in window properly.Thank you. I need help (Suggested 95-23) The 7/16 needs to be 1/4" I ... (cont.)

I'm looking to replace many of my worn out window screen corners. The corners I need are at the bottom of the screens only. I need some sort of pull ring to extract the screen from the window using my fingers. The screen frame is 1/4". The corner of the part in question measures approx 3/4" from the ... (cont.)

I received my order of 95-112 and I don't know how you measure these things but please see photo, these things measure 1/2 " I ordered 1/4".Thank you. Flange is 1/4" wide and 1/4" thick the square is 1". Photos attached.

We are needing to fix some outside screen frames but the corners are broken and deteriorated. They are Rolox brand windows. We ordered the 3/4 x 3/8 size from your company part no. 95-034 but they are too big. Pictured is the screen in the existing window plus several pictures of the broken corner ... (cont.)

I am at a loss & could use some help! I am looking for a window corner that fits my screen frame. I purchased a 5/16" that is too wide. Any help / recommendations would be appreciated!I'm thinking I should go with a 1/4" ?

We can find a version of these at any hardware store, but none of them fit our existing frames. They measure approx. 1.75" x .5" x .25". Do you carry this item? Thanks for any advice you can provide! Dan

My aluminum framed screen has plastic corner inserts that fit entirely inside the aluminum frame. They are L-shaped, 1.5" long on each leg, 0.5" wide and 0.25" thick. The only marking on them is the number embossed 202. I cannot find these, would you have any? It came off of a manufactured home/ ... (cont.)

I am looking for replacement corners for some existing screens on our house.I am attaching 2 pictures. The screen extrusion is 1/4" x 1/2" inside dimension. The corners are 1/4" thick and total width is 5/8", but the little lip slides into a small groove, leaving 1/2" to fill the extrusion.Anythin ... (cont.)

Need screen corners. It is for the old aluminum storm/screen door from late fifties that would have family initial on screen guard. The screen is set in a slot all around window the measure is about 1/4 wide. What would the correct part. This is a replacement corner Not an original one. Than ... (cont.)

This corner connector is 5/8" x 1/4. The 2 corner legs are 1/4"x1/4x5/8".