Viewing all customer Discussions for:

S377-31 31" Series 377 Channel Balance

I need 2 replacements for this balancer

Hi, I have two non-tilt channel balancers to replace with the following specification: 1/2" width 31" length (metal to metal) Sash weight 9 lbs The pulley side appears to have #15-005 winged channel balance shoe, 1" depth. However, I'm not sure what the spring anchor side plastic piece is. Hopeful ... (cont.)

Need ends and balance and window clips and 1552 window ends

Hello and thank you in advance for your help. Below are photos I just took of one of the balance rods I need to replace. Are the photos sufficient or do you need further information? Thank you again!

The photos attached were taken from inside of the house of the right channel balance. The length of the channel balance metal is 31 inches. The channel balance metal has the number 3030 stamped into it. I need both left and right channel balances and also both left and right windows frame limiters. ... (cont.)

Channel length 31" 3020 is the stamp printed on it No known manufacturer. Original windows on a Florida house built around 1983. Quantity required is 2

Window is 50" length and 30" high

Here is another channel balance I'm looking for the correct part number. I would like to replace both sides.Thank you.Phill

Please let me know the part number for this. Thank you

I am looking to replace my window balance. This balance measures 31 inches and is stamped 3020 HM.

I have 2 types of windows 26" and 30".I need to replace the balances, sash & plastic take out clip. I don't know the window brand. all I see is "AAMA Sponsored" see picture attached. The balances reference are 2320P for the 26" window and 3010P for the 30" window. Thanks a lot for your support. Jai ... (cont.)

I have two windows with the 3020v 31" and six windows with the 2320v 24" balances. I need both sides in each window. Thank you!Robert

When I measure the channel width with calipers I get 0.6" and a depth of 0.61" (this is measuring the metal spring casing). The metal casing is 31" long. The end fittings are winged. These are original windows from a home built in 1984. There is a stamp on the metal spring casing that looks like 302 ... (cont.)

Hi, It seems that the plastic pieces holding my windows that are 30+ years old are all breaking. I have taken out the channels balances out and they seem OK, but on windows having issue its all the plastic that is broken. Based on the pics, I have provided, is it possible to just get the plastic ... (cont.)

I want to make sure that the s377 is what I need from your website before placing my order for them..It says 3030F but I'm not secure if it is the same as 3030 or FÃ 3030 and please if you have, how much and how long it will take to receive, I'm in Florida zip code 33446.

Please, help me identify this balance. It says 3030F but I don't know if it's the same as 3030 or FÃ 3030 also if you have how much and how long to get here, I'm in Florida zip code 33446. Thank you

I need (2) 31 inch balancer stamped 3030 with the ends per photo along with (2) of the clips that screw the window. The balances measure 5/8 one side 9/16 the other without a rolled edge.Call me if you have questionsThanks

3020 Stamped on part 31" long (without end fittings) Looking for the P/N to order replacement balancers Thank you

Non-Tilt window only markings on the channel balance are 3020 width 1/2" approx 31" long home built in 1981 Also the top of the window plastic piece is broken (see pic - where window balance has pushed thru);

Hi,I need two channel balances, with ends installed, 2 corresponding top sash guides and two nylon balance retainers.The channel balances are 1/2" wide and 31" long. The ID number on them is 30-3 J.I've gotten several other balances from you in the past and replaced them easily, but I couldn't find ... (cont.)