Viewing all customer Discussions for:

21-024 Bifold Door Top Pivot, Float-Away

The pins measure one quarter inch in diameter, the plastic that fits the ends measures 3/8 of an inch . the sticker on one of the doors says FLOAT AWAY DOOR COMPANY of Georgia . I need top to bottom hardware.. four per door, four top , four bottom , eight per set of doors, two sets of doors eight b ... (cont.)

Could someone help me to identify the right size. It is a right side closet door.

I'm attaching a picture of folding closet door parts that I am in need of. In the picture I'm holding three different pins. I will number the 1-3. #1- has a white plastic cap with a spring. #2- is threaded with the insert to go in the door. #3- is just a pin with the insert to go in the door which i ... (cont.)

I need new 2 top and 2 bottom pivot brackets for my doors. I also need 2 top and 2 bottom pivot pins that will fit the brackets. I prefer not to remove the track but can if necessary. No manufacturer but cardboard glued to inside bottom of doors and one caution arrow. Please advise. Thanks ... (cont.)

This is a metal bifold door, its 30" wide. Hoping to find the pictured track for a couple of extra doors I need to installed. Thank you.

I need the top pivot which stabilizes the door . The pivot guide pin is OK.Enclosed is a pic.Hopefully this will clarify .

Hi. I'm looking for a replacement pin for an older metal bifold door. The attached picture is the pin that is broken and keeps getting stuck in the channel. The pin length is 5", cap is 3/8" diameter, pin seems to be 1/4" diameter. Thank you for any help you can provide.

The part identified by the red circle is the mounting mechanism for this bifold mirrored closet door. I need to find the entire piece. There is a marking on the bolt in the black area that says either "330-170-4" or "330-140-4". The door is original to the house, which was built in the early 1980 ... (cont.)

It appears my Float Away metal bifold door hardware matches product codes: 21-022, 21-023, 21-024. However, is there a different part for the bottom guide pin... or are you to purchase (2) of part code # 21-022 (one for top; other for bottom)? Thx Pam

My name is Don The team member I talked to was Steve. Need lower pin for 2 panel metal door. The lower pivot pin (with nut seems to work). Company part fron Float Away. Float Away - Home Products Inc

I can't find and markings on my four closet doors or the hardware. Can you identify these?

I am trying to fine the correct pins for a Flow Away ,steel ,mirrored ,bi fold closet door. The doors have two different types of pin holders. Most of the doors that work have white plastic bushings at the top an bottom of the steel door with some kind of black plastic for adjusting. These seem f ... (cont.)

Hi, What are the part numbers needed for the top and bottom pivots for steel bifold doors?

Hi, We just bought a foreclosed house and one of the bifold closet door is missing the bottom pivot pin. I would like to verify if the following parts are the right parts to replace/fix this closet door. Bifold Door Guide Pin, Float-A-Way 21-022 Bifold Door Bottom Pivot Pin, Float-A-Way ... (cont.)

Hello, I need help getting all new hardware for the set of metal doors I have for a customer. Please see attached photos. I would like to get all new pins, mounting brackets for pints and upper lower track as well. Please let me know your thoughts on cost, eta on parts and shipping cost to ... (cont.)

I have metal folding doors which hide my washer and dryer in the kitchen. The mobile home is a 1979 I could not find any maker name on the doors or on the pin. the pin measures from top to bottom 5 1/2" long. I also included a picture of what the top of the door looks like thank you for a ... (cont.)

I cannot find a manufacturer or other distinguishing features, but pic 006 is of a similar door showing a top pivot. The actual pivot rod that I need has a different pivot bracket, as shown in photo 007, where the 3/8 inch that goes into the bracket must be 1/4 inch. I also need one bottom bracket ... (cont.)

Need bottom pin looks like photo 5-7/16 " long x 1/4" pin OD with barrel spring type. The oneI have is missing spring and pin cap

Hi I have lost the top pin for a bi-folding closet door and need a replacement. Can you help? Attached is a photo of the top pivot pin for a Binswagner bi-folding steel closet door. The actual pin length is approximately 5 inches (plus or minus) – the photo is inaccurate due to lens flare fro ... (cont.)

i have four sets of Float Away bi-fold metal louvered doors with an April 1983 stamp on one of them. The doors are 93 inches tall - two with 17.75" wide louvered panels, and one with 13.75" louvered panels, and one with 11.75" louvered panels. The hardware is exactly the same on each of them. I ... (cont.)