Viewing all customer Discussions for:

21-033 Float-A-Way Bi-fold Door Bottom Guide Pin

I live in Florida, do you deliver?

Greetings all, I'd like to ask for assistance in identifying the correct part(s) and numbers. This is bottom pivot pin from a metal bifold door (2 panel), manufactured in 1962. I need a cap, or a whole kit reference from your catalog. I can provide more photos with the measurements (in mm) for this ... (cont.)

Looking for replacement pins

Metal bifold door bottom pin 5 1/2 in length

These are pins for folding closet doors. The only marking I can find on the doors is that they were manufactured by Float-away Door Co., a division of Kinkead Industries, Inc., in Atlanta, GA. The house was built in 1971 so the manufacturing date would likely be 1970-1971.

We are looking for replacement pins for these bifold doors they are about 50 years old

The correct pin for bottom float away is 21-033 I ordered 2 tracks, which are narrow (1/2 ") wide instead of 1" wide. I need part number for 1" wide and 7/8th high track , I also need correct part number for the pivot bottom pin. The one I ordered did not work. I have received the following items a ... (cont.)

Hello Do you have replacement hardware for this bifold door? It's super old, date on back says 1971. Neither door set had a complete set of hardware on it. They're in an old mobile home. Hoping you could help with the upper and lower pin replacements. Also not sure the tracks have the pieces they'r ... (cont.)

Hi, I found that the floor pin on my bifold closet door has been worn out. Does your company offer this kind of parts or something similar that we can replace broken piece? Thanks, Phoebe

Greetings.. I have two metal bifold doors that are hurting.. the start of the issue is that the wood tracks are fully worn and the pins will not slide. Yes wood, there was no metal in the track. House built in the 70's. Both are 6" wide, 7' 4" tall. Half of the hardware is swapped out for simple bol ... (cont.)

Hello - I'm in need of replacement parts for a Take-A-Way brand metal bi-fold closet door. The manufacture date says 1969 if that helps, the parts appear to be original. I measured both bottom pins at 5-6/8th inches long, top pins at 4-6/8th inches long. Diameter of the tip of the top and bottom ... (cont.)

Need hinge& guide pin parts. I found the PIVOT BRACKETS, Product Code: 21-215, on your website but I also need 1 top hinge pin, 4 top guide pins & 4 bottom guide pins. All pins are approximately 5" long. No manufacturer's markings.

I am looking for hardware for metal bi-fold doors. Doors were manufactured by Float Away door company Atlanta, GA in 1960's. I have attached the above photos for your review. We would appreciate your quick response.

I am looking to purchase bi-fold door pins for the float away doors made by knikead industry. I need all four pins for each door. I would purchase 10 sets if available

A few years ago I ordered these parts from Swisco. Looks like theyre not available any more. do you have the parts that replace them?

Bi-Fold closet door bottom pivot, with 1/4 adjustable screw no pictured.

Hello- I would like to replace the hardware on my Fenestra metal closet doors. I have enclosed the pictures, which I hope demonstrate the proper dimensions. Unfortunately, I purchased 21-001, 21-007, 21-154, which are for a similar door, but do not fit mine. I was hoping you could point me to the c ... (cont.)

I'm trying to find the replacement plastic mount because this one is stripped out.

Hello, I tried part # 21-022 to replace a bottom door guide but the pin is too large. Wondering if 21-033 would be the next pin to try? I have not had a chance to try to replace the pivot pins yet but those look like they might work. Thanks

We are looking for top and bottom pins for some old metal bi-folding doors. We have 4 doors total. What would you recommend? The top pin is about 4 3/4 inches long The bottom pin is about 5 3/4 inches long