Viewing all customer Discussions for:

10-309 Door Sweep for Hinged Shower Doors, 36"

I am looking for a replacement sweep for my shower door. I need the rubber sweep reaplcement. The drip rail is aluminum.

Hi, looking for some help to replace this brush style shower door sweep with just a plastic type sweep; the brush stays too wet and is causing mold and caulk to never get to dry in between shower uses. This brush style is 26 inches long and has a more round vs rectangle top that needs to fit into th ... (cont.)

length is 15/32 " width of the T or star to fit in the slot is 3/32" ...

do you carry this size and style? End is hexagonal could be star like about 5/32 width at top that goes into top height .9 inches

Please let me know if you sell a door sweep that is 7/16" thick and will insert into my existing fixed frame door. Thanks!

I wanted to replace our drip rail which was attached with 4 screws, and had a vinyl sweep underneath. However, it measure as 27". Can this be correct? Which of yours would I purchase or do I need to keep looking? I think I can reuse the aluminum drip rail again, but would still need the vinyl sw ... (cont.)

This part is from shower lower door for blocking water. It is damaged and the water is leaking outside the shower.

I need to replace a rubber strip in a metal framed shower enclosure. The strip is in a slot in the metal in the door opening on the strike side, and keeps water from escaping between the door and frame. The existing rubber strip is gray and 3/4" wide, with a triangle shaped top that goes in the sl ... (cont.)

Where can I find a replacement? I submitted a few minutes ago and received ID # d164132 but I had an incorrect e-mail address on the request.

I've posted some photo's of the base of my shower door. The rubber material has worn out and I'm trying to replace it. The photo's "FrontDoor Parts Installed" and "EndofDoor Installed" show the parts installed. There is a hardware piece which is 26 3/4" which affixes the rubber gasket to the bot ... (cont.)

LOOKING TO REPLACE A VINYL BUG SEAL ON 1975 PPG SLIDING GLASS DOOR. VINLY STRIP IS 5/8" TOTAL WIDTH, WITH A 1/8" ROUND PIECE AT TOP THAT SLIDES INTO THE TRACK AT THE BOTTOM OF DOOR. THIS NUMBER WAS ETCHED INTO THE BOTTOM OF THE DOOR. ANSI Z-97.1-1975 1/8"-U AND 16 CFR1201 CII

can't find the right size 3/32 is to big, was told this part is discontinued. i think 1/16th width would work,is there such an animal?? 1 inch wideBotton shower seal 36"x 1"x Looks like the bead is only 1/16th thick 3/32 wont slide in the channel

The glass door is 1/4" thick and 66 3/4' tall: This needs a flap to seal the water from coming out of the shower. The door frame has a 1/4" T shaped slot that the previous sealer was contained. The pictures of the door sweep shows 3 screws that locks in the sweep bar. I sent you a copy of the h ... (cont.)

what is the difference between a swinging door sweep, hinged door sweep and regular shower door sweep?

I need to replace sweep on my shower, I need help identifying the manufacturer. I'm not sure if the sweep slides out or if I have to replace the drip rail also. It does not screw on.

The bottom flap or water stopper needs replacing. Do you sell that part and the screws? Please advise, Tracy

I am looking for a replacement for this broken glass shower door sweep. It is approximately 23.5" long, with two screw holes, approximately 17.5" apart. Do you have anything that matches this configuration?

Can you help me find a replacement seal

I am looking to replace the rubber door sweep for our shower door. The drip rail is fine. It looks like there is a notch on one side to hold the sweep in so not sure if I need a rounded top? I don't think the "T" top would work. The rail is 25 1/2" long. What remains of the old sweep hangs about ... (cont.)

Looking for replacement shower door sweep. I cannot see any markings with name or number. House was built in 1974 and I believe the door is original. Entire sweep is 26 1/4 inches long, 1 7/16 tall. The portion that goes into the aluminum grove is 3/8" width and is semi circular. Thank you, ... (cont.)