Viewing all customer Discussions for:

21-276 Bumper

My PostBenchmark Steel Bifold Door came off the track. The doors are louvred from top to bottom. Need both posts to repair. One came completely off; the other is badly bent. The doors were installed in 1985. The one post looks like the 21-044. Your help is needed to get the correct parts and to ge ... (cont.)

I am trying to source parts for this Benchmark steel bi-fold door. Can you assist --it is installed on a track. will need the parts to hold it in place and open and close smoothly. thanks

Hello, I need to get a full set of parts for (2) sets of double doors. Do you have the parts in kit form? as opposed to individual?If I knew what parts I needed I would be able to order them. I'm redoing a condo that has your doors with parts missing. I don't know what parts they are, so if I coul ... (cont.)

We are looking for parts to secure bifold steel closet door by Benchmark. Most likely need to replace missing spring and cap to fit the track. The pins are about 5 1/2 inches or 14 cm long (a quarter inch or 6mm in diameter). Another spring was 2 3/8 inches or 6 cm long (1 cm diameter). The track ... (cont.)

Hello customer care. I am Doug Woods at 919-309-5563. I have six bifold doors that need a new threaded rod installed at the leading edge of the door. Please refer to the photograph within the attachment and get back to me if you have a part that would work for this. Thank you very much. Doug Woods ... (cont.)

Good Morning; A few months ago (August 24, 2015, Order 673586) I ordered some components e.g. Pivot pin 21-044 for Benchmark metal bifold doors. The component are fine and I am planning to order more. I have these doors all over my house here in Maryland. One question I do have is I notice whe ... (cont.)

i have a set of Benchmark Bi-Fold doors in my pantry. i just had them painted and replaced all the hardware 21-044 and 21-002. the doors open and close now very smoothly however the right side wond clsoe completely ? i have tried several adjustments and there is a slight gap between the doors so t ... (cont.)

hii I have this closet door I need to buy replacement parts for it I about two feet wide metal and the bottom only has one circle thing at bottom and top I think you are calling it the pivot bracket. Should there only be one per rail ? Is it cheaper to buy these parts in a set or individual , also d ... (cont.)

Need help with balance, thank you.

Hi, I'm looking for replacement parts for 2 Benchmark steel bifold doors. (Each door 291/2 wide, 781/2 high). I need both the upper and lower pivots and upper and lower guides for each door to include brackets.and springs. Do you carry these parts? Thanks!

I have a project that has 700 units about 2800 bifold openings that will need new hardware over the next 2 years. Do you have the attached type hardware?

Due To Home Improvements I Had To Take Down All My Closet Doors And Hardware. I Have Put Them Back Up And They Just Don't Seem Right. Is There Complete Instructions for Installation and Adjustment For Benchmark ByFold Steel Doors. Thanks

Leigh Full-Vu metal bi-fold doors. Coopersville, Mi. I need 6 pivot pins, 6 guide pins w/ nylon caps, 10 springs, and 4 rubber stops. Thanks

We moved into a house that has the metal Benchmark bi-fold closet doors and they are a mess. They do not close at all properly and have made some observations. I noticed that the bottom stationary pivot pins, I believe the 21-002's are not inside the pivot bracket holes,but they should be correct? C ... (cont.)

I have a non-operative Benchmark door and looking at your website, it appears I need to replace both my 21-044 guide pins. However, how do I install and adjust them? A drawing or parts diagram would be helpful. Do the plastic tips on the 21-044 ride inside the track or on the surface of the track ... (cont.)

I have Benchmark steel bifold doors on all my closets and they are hard to open and close. Do i need to replace the whole pivot pins or could I get away with just replacing the caps that look like they are worn out?