Viewing all customer Discussions for:

81-098 Pella Patio Glass Door Roller Assembly

Good afternoon, I am in need of two rollers 1.5" rollers two bump stops, 2" x 1" and also the interior sweep 48" long.

PS11 6L oper Pella slider door I need to replace 25 year old rollers . Very hard to open and close after using grafite with no success

I have an old door probably about 30 years old. Could be pella. Not sure. Trying to see if the part can be identified before I remove so I don't render the door totally unusable. Any idea what part this is?

Below are the Numbers I found on the door. ELLA -PEL- 1003 - ASCS FVF122- 071E080CWHT - 5263 -NFRC I hope this helps

Possibly a Pella Door. Width = 2-13/16", Height = 1-11/16", Thickness = 5/8" or 11/16", Wheel Diameter = 1-1/2", Wheel material = metal. Given that information, what is the correct replacement part for my door?

1980's large (approximately 47 x 96) sliding glass door. I believe it is a Pella. Need help identifying. Please see photos. Thanks

Hello, I've attached a drawing of the rollers we need for our patio door. Can you confirm which of yours that we should order?

Trying to replace rollers for pella sliding patio door! The number on the window is ICCC CBA IGMAC insulshield CIC-22-04 your assistance is greatly appreciated

There is no model number listed on the side above the handle, nor on the glass inside. I need to model number to get and price the wheel assembly.THank you,Marley

Paella sliding glass door rollers need replaced. Call Tommy

Our Pella slider seems to need new door rollers. The slider is likely 20-21 years old. We had someone look at the door which he removed and determined the wheel bearing was bad. Unfortunately I did not take a photo of the wheel while the door was off. I have attached a photo of the door in hopes tha ... (cont.)

I have an older (and very heavy) pella patio door that need new rollers. I pulled it out (see pictures) but did not see any serial number. The door has no serial number either.

Hello, I have a six foot 1985 pella exterior sliding door. I need to replace the rollers and don't want to remove the door to see what style they are. I'm hoping you'll know and can send the right replacement parts. Thanks.

Pella aluminum clad wood sliding patio doors. The house was built in 1985. The doors are the originally installed doors. 2 ¾" L x 1 ¾" H x ¾" w Each ¾" measurement is actually 11/16". I suspect they report the size as ¾".

Trying to identify the model of a Pellla sliding door so I can order replacement sliders. The serial number rubbed off. Any ideas?

10881 three panel sliding door pella what rollers go on this door

They measure 2 3/4 x 1 7/8 with 3/8 wide roller. All else being same but does not have the side wings. Thanks for all help

Our Pella bottom rollers are sticking and need replacement. Do all Pella doors use the same bottom rollers? Our doors are probably 10yrs old. I would rather not remove the door until I'm ready to perform the install but if I have to in order to determine the specific type of roller we can do that. ... (cont.)

Pella sliding patio doors; sliding portions slide towards each other and lock. fixed panels attached to sliding on each end; four panels in all. Number above from the edge between the 2 glass panels. Rollers appear worn out and door jumps track.Would like to order new rollers.

I need to find rollers for our Pella sliding glass doors. This house was built in 1967 and to the best of my knowledge the rollers are original#. I have an original invoice for "Pella sliding glass doors, 5/8" insulating glass, with screens, standard hardware as follows: 7# OXO-45, std width, ... (cont.)