Viewing all customer Discussions for:

81-098 Pella Patio Glass Door Roller Assembly

Our Pella bottom rollers are sticking and need replacement. Do all Pella doors use the same bottom rollers? Our doors are probably 10yrs old. I would rather not remove the door until I'm ready to perform the install but if I have to in order to determine the specific type of roller we can do that. ... (cont.)

Pella sliding patio doors; sliding portions slide towards each other and lock. fixed panels attached to sliding on each end; four panels in all. Number above from the edge between the 2 glass panels. Rollers appear worn out and door jumps track.Would like to order new rollers.

I need to find rollers for our Pella sliding glass doors. This house was built in 1967 and to the best of my knowledge the rollers are original#. I have an original invoice for "Pella sliding glass doors, 5/8" insulating glass, with screens, standard hardware as follows: 7# OXO-45, std width, ... (cont.)

Looking for 0C5Y00P0

I have a 1984 Pella Proline series 1299 wood clad sliding door (vinyl on the exterior). Need to replace both rollers. Do you have a part number?

Hello, I need to replace the casters on my Pella sliding glass door. My house was built in 2006 and this is the original door. I can see my door has two single wheels casters.

I have a set of rollers that look like your 81-098 or 81-244. Unfortunately, in removing them.... the rollers were pretty much destroyed. The dimensions are as follows: Length: 2 3/4" Width: 5/8" Height: 1 15/16" Roller Diam: 1 1/2". The rollers are metal, not nylon. Please advise what I ... (cont.)

Good Morning, I am going to replace the rollers on my Pella sliding door. I'm not sure which assembly to order. I found number on the bottom of my door that may help to identify the part. The number is Pella-Pel-0108-ASCSFFV1Z2071E080CWHT-525S.

Single wheel two and three-quarter inches long one and three-quarter inches high seven eights wide

I am looking for a replacement for Pella Part # V782875 - PD Tandem Rollers. I would actually prefer the V782874 - stainless steel version since the door is in a beach location. I could not find a cross reference chart for the available rollers on your site. Can you provide me the correct replace ... (cont.)

Wondering if you have these parts

H: 42.5mm W: 16.5 mm wheel diameter: 1.5" (38mm) metal wheel

I did not see any numbers or markings on these roller assemblies.I actually could not find any markings or model numbers on the sliding door itself either. But I do know it is made by Pella. I suspect it could be from around the early 1980's.For some basic dimensions of the roller assembly:The she ... (cont.)

I reviewed the sliding patio door rollers on your website and don't see anything that comes close to matching this item. I'm reluctant to remove it from the door if there is no chance of replacing it. The door is a Pella that was installed in 1982. With a clean track, it rolls freely but makes a cl ... (cont.)

I need two roller assemblies for my 8 ft. Sliding door. Body is 2 3/4" wide Body is 1 3/4" tall Body is 3/4" thick Wheel is steel Wheel is 1 1/2" diameter Wheel is 3/8" thick I'll include pics

Hello Need replacement roller assembly for Palla siding doors. Thanks

Hello: I'm in need of 2 replacements. The assembly is metal.Channel measures 5/8"Wheel diameter 1 1/2"Outside housing width 2 3/4"Outside housing height 1 5/8"I believe it's a Pella door.Please advise of price, stock, shipping, payment terms, etc.Thanks and Regards,Mary

I think I know which part to buy but just want to get your opinion. The roller on my 1992-manufacured Pella Proline aluminum-clad wood sliding door is misbehaving and the one nearest the door locking assembly side is particularly problematic. Measurements for the overall housing I've got is a w ... (cont.)

Hello, I recently removed a Pella sliding door to clean and lube the rollers, but clearly both rollers have bearings that are shot. I could not remove the roller assembly from the door (afraid to damaged it) so I took a few pictures that I thought would help me identify the assembly but later reali ... (cont.)

Single roller, metal roller, Need 2 replacements.