Viewing all customer Discussions for:

23-501 2 Door Bypass Closet Door Hardware Kit, 5ft

Hi! I'd like built wardrobe in my garage. Only instead of glass, I want to use MDF 4 mm. What do I need to buy? What are the top and bottom guides? What are the top and bottom rollers? What handles? Help me please!

Looking for a 60" satin gold colored top track. My track is different looking then the one shown on your site, part # 23-245. My track measures 2-11/16" across the top that mounts against the ceiling, 1-1/2" between the roller guides, and the facial side is 3".

I need to replace the existing track of my sliding door. The width is 2 & 5/16 inches. The regular track available in home Depot & Lowes are only 2 inches wide. What is the width of 23-501?

Looking for 4 of these...

Hi..Have a part very similar to your Kenna 23-048 roller assembly. Mine has a W on it with a crown over the W and then it says 3/4 Front and 1 3/8 Rear...It is 3 1/2 in high and 1 1/2 wide. It is 3/8 from the back of the frame to the offset frame and 3/4 from the back of the frame to the middle of t ... (cont.)

The sliding closet door were taken off to add a shelf inside the closet and repaint, and when we went to put the doors back on, the rollers won't stay on the track. I don't understand why they won't. (we're older)

What is the measurement from the center of door to center of door or from roller to roller? I am trying to find out the space between the doors after installation.

I have a 1940s era cedar closet with doors that roll on an upper track. One of the wheels on the hanger fell off, and I cannot find a replacement anywhere. I am looking for a wheel that is 1/2 inch diameter and the bracket is flush, not offset. Do you have anything that could be a close rep ... (cont.)

Hi- I am looking for replacement for these sliding closet door rollers. The rollers diameter is 3/4" and width 1/4". The offset for the Back panel is 3/4" and Front panel is 3/8". Do you offer anything like this or have another suggestion that can be used in place of these? Thank you. C ... (cont.)

Hi! My house was built in 1957 and the plastic wheel on this carrier finally gave out. Can you help me locate a replacement part? Thanks! Laurie

It looks like I ordered the wrong size door hanger. The wheel of this replacement closet door hanger is too small. Everything else looks fine. See attached picture of the hanger I need to replace. Will you find the correct one for me and ship it? Actually, I could use two of them. You can ... (cont.)

I purchased two sets of Closet Door Hangers with 3/4"roller wheels(Swisco item# 23-047)well over a year ago to replace some missing hardware for my bypass closet doors. Unfortunately,the existing track on the closet only accommodates a 5/8" roller wheel. Therefore, I need a closet hanger with a 5/ ... (cont.)

Seem I have an odd sized door. House was built in 1959 The rolls appear to have a 3/4' offset and flat wheels. House was built in 1959. Thanks again

This home is a "Warmington" built home finished in 2004. The track is so bent now that the door doesn't work. The total door width is 58 inches. Each door is 92 inches high and 30 inches wide. There is a small plastic piece at the bottom that supposedly keeps doors on. I've had problems sinc ... (cont.)

Hi I'm looking to put up sliding closet doors but because of the age of my house I need a floor track 60" in size cause the top of the closet frame has built in guid track 1 1/2. Inch. I'm also looking to use regular wood slab doors. Can you tell me if this can be done and if so what parts on your ... (cont.)

When I moved into our home here in TN, we had already had new hardwood floors installed. The closet doors in our bedroom were just swinging from the top track. I don't know what the bottom looked like originally. Your pictures most resemble my assembly, though it appears they trimmed the doors co ... (cont.)

The width of my closet opening is exactly 60" or five feet. It appears from your by-pass track kits that I would use the 5ft track #Product code 23-501 that the track is only 59" vs the 60" opening that I need. How does this work? Do I center the track on the header and leave a gap of 1/2" on eac ... (cont.)

What is the width of the product 23-501 (2 Door Bypass Closet Door Hardware Kit, 5ft)? Thanks.