Viewing all customer Discussions for:

87-192 7/16" Flat Nylon Roller with Nylon Axle Pin

Looking for these window replacement parts for the following items:Window roller 9/16" X 1 3/8" X 1Window round wheel 1/4"Window Seal Strip bottom= 1/4" height 3/16, gray color Please see attached photos

The plastic bases are intact. Maybe just need the roller and wheel inserts.

I'm needing some Milgard nylon wheels....actually ONLY need the wheel, as metal axle & Plastic frames are ok. Please advise

I am looking for axils and rollers for the window shown above. The roller outside diameter is 7/16" and the smaller "shaft " outside diameter is 1/4".The width of the larger diameter section is 1/8" and the "shaft is 1/8".The axil shaft is 5/32" diameter and 9/16" long ( not including the thickness ... (cont.)

Looking to replace some roller wheels that have flat spots. I would need 10.

I was wondering if the ball bearing wheel from 87-218 would fit my original nylon housing. All my nylon housings are in good shape. I like the idea of a ball bearing giving a smother operation.

Double slider windows that state that they are Milgard series 8120/8130/8170. Sash roller had a A7 on the backside of it. Rollers are vinyl with metal axles. Rollers are worn down.

looking for just the nylon wheels if possible or if it comes as what is shown that's fine. Not sure on brand of windows. Nick with post glass and mirror. Overall diameter is roughly 7/16" 5/32" wide on big circular and 9/32" nipple to nipple

Hello. Could you please identify this part for me? I need the right and left version. If these are no longer available, could I simply buy replacement rollers with axles? Current wheel is nylon and axle is steel. The roller wheels are 3/8" external diameter. Diameter could be slightly larger t ... (cont.)

Hi Swisco, I have a 1979 Aluminum horizontal sliding window in the kitchen. It has two small rollers on the bottom that I would like to replace. Any idea what part might fit? Thanks! Atlas

I was able to make the Swisco 87-178 work with a little trimming, so I just ordered ten more. But I'd like to get a bunch of wheels if you have have something that would fit this roller. the axle is just under a quarter inch. The wheel diameter is about 5/8". I'm working on about 40 apartments. ... (cont.)

Many houses in the Reno, NV area have these unbranded aluminum sliding windows. The rollers and/or axles in most of our house are shot. With some effort I could remove them, they are probably original. Looks like the axles pull out on one side, or the head of them wears out because it serves as ... (cont.)

Thank you, Robert

Need replacement rollers (4 per window), and I have 9 different sized windows with same rollers. Also, want advise on replacement of wool-like felt weather stripping that has deteriorated into nothing. These are aluminum single pane windows in 1971 house. Thanks.

Hello, I will attach two photos to show you what I'm trying to find. We recently moved into a condo. The sliding windows date to the 1970s - metal frame, rollers on the bottom and top. Eventually we'll replace them. I need rollers for the bottoms and tops. I had purchased the 87-191 gear on your we ... (cont.)

I'm a local handyman and am not too familiar with the window 'glide system' I ran into yesterday. A customer has original (late 50s/early 60s) original aluminum windows. Complaint was tough to open / close. I removed the window and found remnants of old rollers and (2) axle pins without any ro ... (cont.)

I need replacement rollers and weather seals for aluminum windows from the 60s whose appearance is attached. The roller is a nylon cylindrical wheel about 11.5 mm in diameter (7/16 ") and 5.3 mm thick. The hole is about 3.2 mm. The wheel is held in place and rotates around a nylon "nail" whose rou ... (cont.)